Ford Aspire (1997 year). Manual — part 12
45
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
If your vehicle has a manual transaxle, you must
push the key toward the steering column to
rotate the switch to the LOCK position.
ACC (accessory) allows some of your vehicle’s
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
ON allows you to test your vehicle’s warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
Hazard Flasher Switch
The hazard flasher switch is located on the top
of the steering column. For more information,
refer to
Hazard Flasher
in the
Roadside Emergencies
chapter.
The Turn Signal Lever
You can use the turn signal lever on the left side
of the steering column to:
❑
operate the headlamps and parking lamps
❑
operate the turn signals and cornering lamps
❑
turn the high beams on/off
❑
flash the lamps
46
Headlamps and Parking Lamps
To turn the parking lamps or headlamps on,
twist the knob at the end of the turn signal
lever.
FIRST STOP — Turning the knob to the first
stop will turn on the license plate lamps,
parking lamps, side marker lamps, tail lamps,
and instrument panel lamps.
SECOND STOP — Turning the knob to the
second stop will turn on the headlamps, license
plate lamps, parking lamps, side marker lamps,
tail lamps, and instrument panel lamps.
Headlamp and parking lamp control
Daytime Running Light System
(Canadian vehicles only)
In Canada, the lights illuminate during daytime
operation. The Daytime Running Light system
(DRL) automatically illuminates when the
ignition switch is turned to the ON position. The
daytime running lights are switched off under
the following conditions:
❑
when the headlamps are switched on
❑
when the parking brake is applied
❑
when the flash-to-pass system is used
47
WARNING
The Daytime Running Light (DRL) system
will not illuminate the tail lamps and
parking lamps. Turn on your headlamps
at dusk. Failure to do so may result in a
collision.
High Beams and Flashing the Lamps
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
Flashing the Lights
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is in the on or off position.
High beam and flash-to-pass operation
48
Turn Signals
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
If the turn signal stays on after you turn, move
the lever back to the center off position.
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the OFF position when you release it.
Turn signal
Windshield Wipers and Washer
To operate the windshield wipers and washers,
make sure your ignition key is turned to the ON
position.
The windshield wipers can be operated by
moving the control lever. The standard wipers
have two speeds and the optional wipers have
three speeds.
To operate the standard wipers, pull the lever
down to the first stop (LO). For high speed
operation, pull the lever down to the second
stop (HI).
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст