Ford Aspire (1997 year). Manual — part 6
21
Electronic Stereo and Stereo
Cassette Radios
Using the Controls on Your New Radio
How to turn the radio on and adjust the
volume
Press the “POWER” button to turn the radio on.
Press it again to turn it off.
Press the right (+) side of the “VOL” button to
increase the volume. Press the left (
S
) side of
the button to decrease the volume.
If the volume is set above a certain level when
the ignition is turned off, the volume level will
reset to a “nominal” listening level when the
ignition switch is turned back on.
Selecting the AM or FM frequency band
Push the “BAND” button to select the desired
frequency band. Pushing the button more than
once will alternate between AM, FM1 and FM2.
These functions are used with the station
memory buttons described under
How to tune
radio stations
.
How to tune radio stations
There are four ways for you to tune in a
particular station. You can manually locate a
station, “SEEK” to the next station, “SCAN” for
listenable stations, or select the station using the
memory preset buttons, which you can set to
any desired frequency.
❑
Using the manual mode to tune your radio
You can change the frequency up or down
one increment at a time by first pressing the
mode button until “MAN” appears above the
frequency display. Then, press either the right
(
a
) or left (
b
) side of the “SEEK” button.
22
❑
Using the “SEEK” function
The “SEEK” function allows you to
automatically select listenable stations up or
down the frequency band. This is the default
mode of the “SEEK” button. If the radio has
been changed to another mode, press the
mode button until “SEEK” appears above the
frequency display. Then press the right (
a
)
side of the “SEEK” button to select the next
listenable station up the frequency band.
Press the left (
b
) side of the “SEEK” button
to select the next listenable station down the
frequency band. By holding the button down,
listenable stations can be passed over to reach
the desired station.
❑
Using the “SCAN” function
To enter scan mode, press the mode button
until “SCAN” appears above the frequency
display. Press the right (
a
) side of the
“SEEK” button and the radio will begin
scanning up the frequency band, stopping on
each listenable station for approximately a
five-second sampling. This continues until
you press the “MODE” button once again.
Press the left (
b
) side of the “SEEK” button
to activate the SCAN function down the
frequency band.
❑
Setting the Station Memory Preset buttons
Your radio is equipped with 4 station
memory buttons. The buttons can be used to
select up to 4 preset AM stations and 8
preset FM stations (4 in FM1 and 4 in FM2).
23
Follow the easy steps below to set these buttons
to the desired frequencies:
1.
Select a band, then select a frequency.
2.
Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
3.
Follow the two steps above for each station
memory preset button you want to set.
Adjusting the tone balance and speaker
output of your radio
❑
Increasing or decreasing the bass response
Push the “SELECT” button repeatedly until
the display reads “BASS.” Push the right (+)
side of the “VOL” button to increase bass,
and push the left (
S
) side to decrease bass.
❑
Increasing or decreasing treble response
Push the “SELECT” button repeatedly until
the display reads “TREB.” Push the right (+)
side of the “VOL” button to increase treble,
and push the left (
S
) side to decrease treble.
❑
Adjusting speaker balance
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the “SELECT” button
repeatedly until the display reads “BAL.”
Push the right (+) side of the “VOL” button
to shift the sound to the right speaker, and
push the left (
S
) side to shift the sound to
the left speaker.
24
❑
Adjusting speaker fader
Fade control allows you to adjust the sound
distribution between the front and rear speakers.
Push the “SELECT” button repeatedly until the
display reads “FADE.” Push the right (+) side of
the “VOL” button to shift the sound to the front
speakers, and push the left (
S
) side to shift the
sound to the rear speakers.
Using the Controls of Your Cassette Tape
Player (If equipped)
How to insert a tape
Insert a cassette (with the open edge to the
right) firmly into the tape door opening, making
sure the cassette is completely in and “seated.”
How to locate a desired track on the tape
NOTE:
The tape track or side number
indicated in the display does not
necessarily correspond to the tape track
or side number on the cassette label. It
is used only to indicate when the tape
mechanism reverses tracks.
❑
Fast forwarding the tape
Push the right
g
button to fast forward
the tape. The radio will play while the tape is
in fast forward.
❑
Rewinding the tape
Push the left
h
button to rewind the tape.
The radio will play while the tape is
rewinding.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст