Ford E-450 (2018 year). Manual — part 14

Press and release the SELECT/RESET
stem, by the speedometer, to choose
settings and confirm messages. Select or

reset the function by holding the
SELECT/RESET stem for more than two
seconds.

Info

TRIP A or B

Miles (km) to E

XX.X AVG MPG (L/100km)

MPG (L/km)

HOLD RESET FOR SETUP MENU

HOLD RESET FOR SYSTEM CHECK

TRIP A or B

Registers the distance of individual
journeys.

Miles (km) to E

This displays an estimate of approximately
how far you can drive with the fuel
remaining in your tank under normal driving
conditions. Remember to switch the
ignition off when refueling to allow this
feature to detect the added fuel correctly.
Based on your recent driving history of 500
miles (800 km), the system calculates the
distance to empty using a running average
fuel economy. This value is not the same
as the average fuel economy display. The
running average fuel economy re-initializes
to a factory default value if the battery is
disconnected.

XX.X AVG MPG (L/100km)

Average fuel economy displays your
average fuel economy in miles/gallon or
liters/100 km.

MPG (L/km)

This displays instantaneous fuel economy
as a bar graph. Your vehicle must be
moving to calculate instantaneous fuel
economy. You cannot reset instantaneous
fuel economy.

System check and vehicle feature
customization

Note: System check and vehicle feature
customization is only available with the
optional information display controls.

Note: When returning to the setup menu
and you select a non-English language, you
will see a message appear HOLD RESET
FOR ENGLISH to change back to English.
Press and hold the SELECT/RESET stem to
change back to English.

E194389

Press and hold the SELECT/RESET stem
to get into the setup menu sequence for
the following displays:

Setup

OIL LIFE

English or Metric

Press and hold the
SELECT/RESET stem

UNITS ENG /
METRIC

ON or OFF

AUTOLOCK (if
equipped)

ON or OFF

AUTOUNLOCK (if
equipped)

COMPASS ZONE (if equipped)

Electric or EOH

Press and hold the
SELECT/RESET stem

TBC MODE (if
equipped)

English / Spanish / French

LANGUAGE =
ENGLISH /
SPANISH /
FRENCH

SYSTEM CHECK

XXX% OIL LIFE

Press and hold the SELECT/
RESET stem

RESET FOR SYSTEM
CHECK

ENGINE HOURS (if enabled)

ENGINE IDLE HOURS (if
enabled)

CHARGING SYSTEM

BRAKE SYSTEM

SYSTEM CHECK

TBC GAIN = XX.X or NO
TRAILER (if equipped)

TBC GAIN = XX.X or
OUTPUT = ////// (if
equipped)

XXX MILES TO E

OIL LIFE XXX% HOLD RESET = NEW

This displays the remaining oil life. An oil
change is required whenever indicated by
the message center and according to the
recommended maintenance schedule.
USE ONLY RECOMMENDED ENGINE OILS.

To reset the oil monitoring system to 100%
after each oil change, perform the
following:

1.

Press and release the SELECT/RESET
stem to display OIL LIFE XXX% HOLD
RESET = NEW.

2. Press and hold the SELECT/RESET

stem for two seconds and release to
reset the oil life to 100%.

Note: To change oil life 100% value (if
equipped):

3. Once OIL LIFE SET TO XXX%

displays, release and press the
SELECT/RESET stem to change the oil
life start value. Each release and press
reduces the value by 10%.

UNITS ENG / METRIC

Displays the current units in English or
Metric.

AUTOLOCK

This feature automatically locks all vehicle
doors when you shift into any gear, putting
the vehicle in motion.

AUTOUNLOCK

This feature automatically unlocks all
vehicle doors when you open the driver's
door within 10 minutes of switching the
ignition off.

COMPASS (if equipped)

Displays the vehicle's heading direction.

Note: Driving near large buildings, bridges,
power lines and powerful broadcast
antennas may affect the compass reading.
Magnetic or metallic objects placed in, on
or near the vehicle may also affect compass
accuracy. If the compass appears to be
inaccurate, a manual calibration may be
necessary. Refer to Compass zone
adjustment.

Compass zone adjustment

1

2

3

4

5

6

7 8 9 1011

12

13

14

15

E142800

1.

Determine which magnetic zone you
are in for your geographic location by
referring to the zone map.

2. Press and release the SELECT/RESET

stem to scroll through the information
displays until the message center
displays HOLD RESET FOR SETUP
MENU.

3. Press and hold the SELECT/RESET

stem to get into the setup menu. Press
repeatedly to scroll through the setup
menu until COMPASS ZONE XX
appears in the information display.

4. Press and hold the SELECT/RESET

stem for approximately two seconds
to go to the next zone, then release.

5. Press and hold to go up by one zone

then release. Repeat this until you
reach the desired zone.

6. To exit the procedure, release the

SELECT/RESET stem and allow the
setup timer to expire.

Compass calibration adjustment

Note: For optimum calibration, drive to an
open, level location away from large
metallic objects or structures. Switch off all
non-essential electrical accessories (heated
rear window, heater, A/C, map lamps, wiper,
etc.) and make sure all the doors are closed.

Note: If you press the SELECT/RESET stem
during the calibration or three minutes
elapse since the beginning of the calibration
without driving the vehicle, the information
display reverts back to normal operation
and CAL displays until you complete a
successful calibration.

1.

Press and release the SELECT/RESET
stem to scroll through the information
displays until HOLD RESET FOR SETUP
MENU appears.

2. Press and hold the SELECT/RESET

stem to get into the setup menu. Press
it repeatedly to scroll through the setup
menu until HOLD RESET FOR
CALIBRATION appears in the
information display.

3. Press and hold the SELECT/RESET

stem for approximately two seconds
until the information display enters the
compass zone adjustment mode.

4. Press and hold the SELECT/RESET

stem until CIRCLE SLOWLY TO
CALIBRATE appears in the information
display.

5. Slowly drive the vehicle in a circle less

than 3 mph (5 km/h) until the CIRCLE
SLOWLY TO CALIBRATE message
changes to CALIBRATION
COMPLETED. This may require up to
five circles to complete the calibration.

TBC MODE (if equipped)

Allows you to choose the trailer brake
mode.

LANGUAGE = ENGLISH / SPANISH /
FRENCH

Allows you to choose which language
appears in the information display.

Waiting four seconds or pressing the
SELECT/RESET stem cycles the
information display through each of the
language choices.

Press the SELECT/RESET stem to set the
language choice when the language you
want appears.

HOLD RESET FOR SYSTEM CHECK

The information display begins to cycle
through the vehicle systems and provides
a status of the item if needed. Some
systems show a message only if a
condition is present.