Ford Expedition (2022 year). Manual in english — page 6
ADJUSTING THE STEERING
WHEEL - VEHICLES WITH:
MANUAL ADJUSTABLE
STEERING COLUMN
WARNING:
Do not adjust the
steering wheel when your vehicle is
moving.
Note:
Make sure that you are sitting in the
correct position. See
E359744
1.
Unlock the steering column.
2. Adjust the steering wheel to the
position you prefer.
3. Lock the steering column.
ADJUSTING THE STEERING
WHEEL - VEHICLES WITH:
POWER ADJUSTABLE
STEERING COLUMN
WARNING:
Do not adjust the
steering wheel when your vehicle is
moving.
Note:
Make sure that you are sitting in the
correct position. See
E261582
Press the top or bottom of the control to
move the steering wheel up or down.
Press the front or rear of the control to
move the steering wheel in or out.
You can save and recall the steering wheel
position with the memory function. See
104
Steering Wheel
RESETTING THE STOPPING
POSITION - VEHICLES WITH:
POWER ADJUSTABLE
STEERING COLUMN
Note:
The steering wheel stops when it
detects an obstruction. This sets a new
stopping position.
To reset the steering column to its normal
stopping position:
1.
Confirm there is nothing obstructing
the motion of the steering column.
2. Press and hold the steering column
control until the steering column stops
moving.
3. Press the steering column control
again.
Note:
The steering column may start to
move again.
4. When the steering column stops,
continue holding the control for a few
seconds.
5. Repeat for each direction, as necessary.
HORN
E270945
Press on the center of the
steering wheel near the horn icon
to activate the horn.
SWITCHING THE HEATED
STEERING WHEEL ON AND OFF
- VEHICLES WITH: HEATED
STEERING WHEEL
To activate the heated steering
wheel, press the button on the
climate control unit.
On some vehicles, an indicator on the
button illuminates when the heated
steering wheel is on.
Note:
A sensor regulates the temperature
of the steering wheel.
105
Steering Wheel
ADJUSTING THE PEDALS
WARNING:
Do not use the pedal
adjustment controls when the vehicle is
moving. Failure to follow this instruction
could result in personal injury or death.
Your control is on the left-hand side of the
steering column or on the instrument
panel.
E176213
Farther away from you.
A.
Closer to you.
B.
You can save and recall the pedal positions
with the memory feature. See
106
Adjustable Pedals
(If Equipped)
WIPERS
WIPER PRECAUTIONS
Do not operate the wipers on a dry
windshield. This could scratch the glass or
damage the wiper blades. Use the
windshield washers before wiping a dry
windshield.
Fully defrost the windshield before you
switch the windshield wipers on.
Switch the windshield wipers off before
entering a car wash.
SWITCHING WINDSHIELD WIPERS
ON AND OFF
E327739
High-speed wipe.
A
Intermittent wipe.
B
Off.
C
E270969
Use the rotary control.
AUTOWIPERS
(IF EQUIPPED)
WHAT ARE AUTOWIPERS
Autowipers turns on and controls the
speed and frequency of the windshield
wipers.
AUTOWIPERS SETTINGS -
VEHICLES WITH: 12.3 INCH
SCREEN
1.
Press
Settings
on the touchscreen.
2. Press
Vehicle Settings
.
3. Press
Wipers
.
4. Switch
Rain Sensing
on or off.
Note:
When you switch the feature off, the
wipers do not operate based on the rain
sensor. When you switch on the windshield
wipers to the intermittent wipe position with
the feature off, the wipers use the wipe
speed set by the rotary control.
AUTOWIPERS SETTINGS -
VEHICLES WITH: 15 INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
SETTINGS
.
3. Press
Vehicle
.
4. Press
Wipers
.
5. Switch
Rain Sensing
on or off.
Note:
When you switch the feature off, the
wipers do not operate based on the rain
sensor. When you switch on the windshield
wipers to the intermittent wipe position with
the feature off, the wipers use the wipe
speed set by the rotary control.
107
Wipers and Washers
ADJUSTING THE SENSITIVITY OF
THE RAIN SENSOR
E311292
Low sensitivity.
A
High sensitivity.
B
Use the rotary control to set the sensitivity
of the rain sensor.
When you select low sensitivity, the wipers
operate when the sensor detects a large
amount of water on the windshield.
When you select high sensitivity, the wipers
operate when the sensor detects a small
amount of water on the windshield.
SWITCHING THE REAR
WINDOW WIPER ON AND OFF
E340280
Rotate the control away from you for a
long wipe interval.
Rotate the control toward you for a short
wipe interval.
REVERSE WIPE
WHAT IS REVERSE WIPE
Reverse wipe turns on the rear window
wiper when you shift into reverse (R) and
the windshield wipers are on.
REVERSE WIPE SETTINGS -
VEHICLES WITH: 12.3 INCH
SCREEN
1.
Press
Settings
on the touchscreen.
2. Press
Vehicle Settings
.
3. Press
Wipers
.
4. Switch
Rear Wiper On (when in
Reverse)
on or off.
REVERSE WIPE SETTINGS -
VEHICLES WITH: 15 INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
SETTINGS
.
3. Press
Vehicle
.
4. Press
Wipers
.
5. Switch
Reverse Wiper
on or off.
CHECKING THE WIPER
BLADES
E142463
Run the tip of your fingers over the edge of
the blade to check for roughness.
108
Wipers and Washers
REPLACING THE FRONT
WIPER BLADES
E165804
1.
Pull the wiper blade and arm away
from the glass.
Note:
Do not hold the wiper blade to lift the
wiper arm.
E327597
2
2. Lift the wiper blade primary locking clip.
E327598
3. Press the wiper blade secondary
locking clip.
4. Remove the wiper blade.
Note:
Make sure that the wiper arm does
not spring back against the glass when the
wiper blade is not attached.
5. To install, reverse the removal
procedure.
Note:
Make sure that the wiper blade locks
into place.
109
Wipers and Washers
REPLACING THE REAR WIPER
BLADES
E271380
1.
Lift the wiper arm.
Note:
Do not hold the wiper blade to lift the
wiper arm.
2. Remove the wiper blade.
Note:
Make sure that the wiper arm does
not spring back against the glass when the
wiper blade is not attached.
3. To install, reverse the removal
procedure.
Note:
Make sure that the wiper blade locks
into place.
WASHERS
WASHER PRECAUTIONS
WARNING:
If you operate your
vehicle in temperatures below 41°F
(5°C), use washer fluid with antifreeze
protection. Failure to use washer fluid
with antifreeze protection in cold
weather could result in impaired
windshield vision and increase the risk
of injury or accident.
Do not operate the washers when the
washer reservoir is empty. This could cause
the washer pump to overheat.
Keep the outside of the windshield clean.
The rain sensor is very sensitive and the
wipers may operate if dirt, mist or insects
hit the windshield.
USING THE WINDSHIELD WASHER
E311291
E270967
Press and hold the button at the
end of the lever to operate the
windshield washer.
Note:
A courtesy wipe occurs a short time
after the wipers stop to clear any remaining
washer fluid when switched on. See
Switching the Courtesy Wipe On and Off
110
Wipers and Washers
SWITCHING THE COURTESY WIPE
ON AND OFF - VEHICLES WITH:
12.3 INCH SCREEN
1.
Press
Settings
on the touchscreen.
2. Press
Vehicle Settings
.
3. Press
Wipers
.
4. Switch
Courtesy Wipe
on or off.
SWITCHING THE COURTESY WIPE
ON AND OFF - VEHICLES WITH: 15
INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
SETTINGS
.
3. Press
Vehicle
.
4. Press
Wipers
.
5. Switch
Courtesy Wipe
on or off.
USING THE REAR WINDOW
WASHER
E340280
Rotate the control to the top or bottom
position and hold it to operate the rear
window washer.
Note:
A courtesy wipe occurs a short time
after the wipers stop to clear any remaining
washer fluid when switched on. See
Switching the Courtesy Wipe On and Off
ADDING WASHER FLUID
E348204
WASHER FLUID SPECIFICATION
WIPERS AND WASHERS –
TROUBLESHOOTING
WIPERS AND WASHERS –
WARNING LAMPS
E132353
Illuminates when the windshield
washer fluid is low.
111
Wipers and Washers
WIPERS AND WASHERS –
FREQUENTLY ASKED QUESTIONS
Why are there streaks and smears on
the windshield?
The wiper blades could be dirty, worn
or damaged. Check the wiper blades.
See
(page 108). If the wiper blades are dirty,
clean them with washer fluid or water
applied with a soft sponge or cloth. If
the wiper blades are worn or damaged,
install new ones. See
112
Wipers and Washers
EXTERIOR LIGHTING
CONTROL
E327629
Lamps off.
A
Parking lamps on.
B
Autolamps on.
C
Headlamps on.
D
Rotate the control to make a selection.
Note:
The lighting control defaults to
autolamps every time you switch your
vehicle on.
HEADLAMPS
USING THE HIGH BEAM
HEADLAMPS
E327570
Push the lever away from you to
switch the high beam on.
Push the lever forward again or pull the
lever toward you to switch the high beams
off.
Slightly pull the lever toward you and
release it to flash the headlamps.
SWITCHING HEADLAMP EXIT
DELAY ON AND OFF
To switch headlamp exit delay on, pull the
turn signal lever toward you after switching
your vehicle off.
To switch headlamp exit delay off, pull the
turn signal lever toward you again or switch
your vehicle on.
Note:
The headlamps turn off after three
minutes with any door open or 30 seconds
after the last door closes.
HEADLAMP INDICATORS
Lamps On
Illuminates when you switch the
low beam headlamps or the
parking lamps on.
Headlamp High Beam
Illuminates when you switch the
high beam headlamps on.
113
Exterior Lighting
HEADLAMPS –
TROUBLESHOOTING
HEADLAMPS – FREQUENTLY
ASKED QUESTIONS
Why is there condensation in the
headlamps?
Headlamps have vents to
accommodate normal changes in air
pressure. Condensation can be a
natural by-product of this design.
When moist air enters the lamp
assembly through the vents, there is a
possibility that condensation can
occur when the temperature is cold.
When normal condensation occurs, a
fine mist can form on the interior of the
lens. The fine mist eventually clears
and exits through the vents during
normal operation.
How much condensation is
acceptable?
The presence of a fine mist, for
example no streaks, drip marks or
large droplets. A fine mist covers less
than 50% of the lens.
How long may it take for the
acceptable condensation to be
cleared?
Clearing time may take as long as 48
hours under dry weather conditions.
How much condensation is
unacceptable?
A water puddle inside the lamp.
Streaks, drip marks or large droplets
present on the interior of the lens.
What should I do if unacceptable
condensation is present?
Have your vehicle checked as soon as
possible.
Why do my headlamps turn off when I
have them switched on when I switch
my vehicle off?
The battery saver turns the headlamps
off after a short period of time after
you switch your vehicle off.
AUTOLAMPS
WHAT ARE AUTOLAMPS
WARNING:
The system does not
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the headlamps on in low visibility
conditions, for example daytime fog.
Autolamps turn the headlamps on in low
light situations or when the windshield
wipers operate.
AUTOLAMP SETTINGS - VEHICLES
WITH: 12.3 INCH SCREEN
1.
Press
Settings
on the touchscreen.
2. Press
Vehicle Settings
.
3. Press
Lighting
.
4. Press
Autolamp Delay
.
5. Press a setting.
AUTOLAMP SETTINGS - VEHICLES
WITH: 15 INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
SETTINGS
.
3. Press
Vehicle
.
4. Press
Lighting
.
5. Press
Autolamp Delay
.
6. Press a setting.
114
Exterior Lighting
EXTERIOR LAMPS
SWITCHING THE TURN SIGNAL
LAMPS ON AND OFF
E311431
Push the lever up or down to
switch the turn signal lamps on.
Set the lever to the middle position to
switch the turn signal lamps off.
Note:
Tap the lever up or down to make the
turn signal lamps flash three times.
SWITCHING THE DAYTIME
RUNNING LAMPS ON AND OFF -
VEHICLES WITH: CONFIGURABLE
DAYTIME RUNNING LAMPS/12.3
INCH SCREEN
WARNING:
The daytime running
lamps system does not activate the rear
lamps and may not provide adequate
lighting during low visibility driving
conditions. Make sure you switch the
headlamps on, as appropriate, during all
low visibility conditions. Failure to do so
may result in a crash.
1.
Press
Settings
on the touchscreen.
2. Press
Vehicle Settings
.
3. Press
Lighting
.
4. Switch
Daytime Running Lights
on or
off.
The daytime running lamps turn on when
all of the following occur:
•
You switch the system on.
•
You switch your vehicle on.
•
The transmission is not in park (P) for
vehicles with automatic transmissions
or you release the parking brake for
vehicles with manual transmissions.
•
The lighting control is in the autolamps
position.
•
The headlamps are off.
Note:
Other lighting control positions do
not turn on the daytime running lamps.
SWITCHING THE DAYTIME
RUNNING LAMPS ON AND OFF -
VEHICLES WITH: CONFIGURABLE
DAYTIME RUNNING LAMPS/15
INCH SCREEN
WARNING:
The daytime running
lamps system does not activate the rear
lamps and may not provide adequate
lighting during low visibility driving
conditions. Make sure you switch the
headlamps on, as appropriate, during all
low visibility conditions. Failure to do so
may result in a crash.
1.
Access the vehicle drawer on the
touchscreen.
2. Press
SETTINGS
.
3. Press
Vehicle
.
4. Press
Lighting
.
5. Switch
Daytime Running Lights
on or
off.
115
Exterior Lighting
The daytime running lamps turn on when
all of the following occur:
•
You switch the system on.
•
You switch the vehicle on.
•
The transmission is not in park (P) for
vehicles with automatic transmissions
or you release the parking brake for
vehicles with manual transmissions.
•
The lighting control is in the autolamps
position.
•
The headlamps are off.
Note:
Other lighting control positions do
not turn on the daytime running lamps.
SWITCHING THE DAYTIME
RUNNING LAMPS ON AND OFF -
VEHICLES WITH: DAYTIME
RUNNING LAMPS (DRL)
WARNING:
The daytime running
lamps system does not activate the rear
lamps and may not provide adequate
lighting during low visibility driving
conditions. Make sure you switch the
headlamps on, as appropriate, during all
low visibility conditions. Failure to do so
may result in a crash.
Daytime running lamps are always on
unless you switch on the headlamps or
your vehicle is in park (P).
SWITCHING THE FRONT FOG
LAMPS ON AND OFF
(If Equipped)
The front fog lamp button is on the lighting
control.
Press the button to switch the
front fog lamps on or off.
Note:
Only switch the front fog lamps on
during reduced visibility.
Note:
The brightness of the daytime running
lamps may decrease when the front fog
lamps are switched on.
Note:
When the lighting control is in the
autolamps position, you cannot switch the
fog lamps on unless the headlamps are on.
SWITCHING THE SPOT LAMPS ON
AND OFF
(If Equipped)
The spot lamp buttons are near the lighting
control.
E340436
Press the button to switch on the
left-hand spot lamp.
E340437
Press the button to switch on the
right-hand spot lamp.
Move the position of the exterior mirrors
to adjust the aim.
Note:
The lighting control must be set to
the parking lamp position.
Note:
The spot lamps illuminate the area
in front of and to the side of your vehicle.
EXTERIOR LAMP INDICATORS
Front Fog Lamp
It illuminates when you switch
the front fog lamps on.
Turn Signal Lamp
It flashes when you switch the
turn signal lamps on.
Note:
An increase in the rate of flashing
warns of a failed turn signal lamp.
116
Exterior Lighting
EXTERIOR LAMP AUDIBLE
WARNING
Exterior Lamps On
Sounds when you open the driver door and
the exterior lamps are on.
EXTERIOR ZONE LIGHTING
WHAT IS EXTERIOR ZONE
LIGHTING
Exterior zone lighting divides the exterior
lighting into zones and allows you to switch
them on and off to provide lighting around
the perimeter of your vehicle.
USING THE EXTERIOR ZONE
LIGHTING - VEHICLES WITH: 12.3
INCH SCREEN
1.
Press
Features
on the touchscreen.
2. Press
Zone Lighting
.
E343474
On and off button.
A
Settings menu.
B
Exterior lamp indicators.
C
Individual zones on and off.
D
All zones on and off.
E
You can use zone lighting when your
vehicle is on or off. When it is off, the
lighting turns off after a certain period of
time.
You can also use individual zone controls
to switch on each zone.
Note:
Make sure to remove exterior lighting
covers when using zone lighting.
Note:
When your vehicle is off and the timer
has one minute remaining, the turn signals
flash six times.
Note:
Indicators on the touchscreen
illuminate when the lights outside of the
zone lighting control are on.
Note:
You can remotely control the zone
lighting using the FordPass app.
USING THE EXTERIOR ZONE
LIGHTING - VEHICLES WITH: 15
INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
CONTROLS
.
3. Press
Zone Lighting
.
117
Exterior Lighting
E358717
E358717
On and off button.
A
Exterior lamp indicators.
B
All zones on and off.
C
Settings menu.
D
Individual zones on and off.
E
You can use zone lighting when your
vehicle is on or off. When it is off, the
lighting turns off after a certain period of
time.
You can also use individual zone controls
to switch on each zone.
Note:
Make sure to remove exterior lighting
covers when using zone lighting.
Note:
When your vehicle is off and the timer
has one minute remaining, the turn signals
flash six times.
Note:
Indicators on the touchscreen
illuminate when the lights outside of the
zone lighting control are on.
Note:
You can remotely control the zone
lighting using the FordPass app.
EXTERIOR ZONE LIGHTING
SETTINGS - VEHICLES WITH: 12.3
INCH SCREEN
1.
Press
Features
on the touchscreen.
2. Press
Zone Lighting
.
3. Press the settings menu in the upper
right-hand corner.
4. Press a setting.
Enable Autolamp Override
This setting allows your vehicle to override
the autolamps when using zone lighting.
When you access zone lighting for the first
time, you can choose this setting. You can
change this setting at any time.
EXTERIOR ZONE LIGHTING
SETTINGS - VEHICLES WITH: 15
INCH SCREEN
1.
Access the vehicle drawer on the
touchscreen.
2. Press
CONTROLS
.
3. Press
Zone Lighting
.
4. Press
Settings
.
5. Press a setting.
Enable Autolamp Override
This settings allows the vehicle to override
the autolamps when zone lighting is on.
When you access zone lighting for the first
time, you can choose this setting. You can
change this setting at any time.
118
Exterior Lighting
AUTOMATIC HIGH BEAM
CONTROL
(IF EQUIPPED)
HOW DOES AUTOMATIC HIGH
BEAM CONTROL WORK
Automatic high beam control turns the
high beams on if it is dark enough and no
other traffic is present. If it detects an
approaching vehicle’s headlamps or tail
lamps, or street lighting ahead, the system
turns the high beams off.
A camera sensor, centrally mounted
behind the windshield of your vehicle,
continuously monitors conditions to turn
the high beams on and off.
E327596
Without automatic high beam
control.
A
With automatic high beam
control.
B
AUTOMATIC HIGH BEAM
CONTROL PRECAUTIONS
WARNING:
The system does not
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the high beams on or off.
119
Exterior Lighting
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст