Ford Ranger (2011 year). Manual — part 12

Press and pull the window switches
to open and close windows.
• Press down (to the first detent)

and hold the switch to open.

• Pull up and hold the switch to

close.

One-touch down

Allows the driver’s window to open fully without holding the control
down. Press the switch completely down to the second detent and
release quickly. The window will open fully. Momentarily press the switch
to any position to stop the window operation.

INTERIOR MIRROR

The interior rear view mirror has two pivot points on the support arm
which lets you adjust the mirror up or down and from side to side.

WARNING: Do not adjust the mirror while the vehicle is in
motion.

EXTERIOR MIRRORS

Power side view mirrors (if equipped)

WARNING: Do not adjust the mirror while the vehicle is in
motion.

To adjust your mirrors:

1. Rotate the control clockwise to
adjust the right mirror and rotate
the control counterclockwise to
adjust the left mirror.

2. Move the control in the direction
you wish to tilt the mirror.

3. Return to the center position to lock mirrors in place.

Driver Controls

51

Fold-away mirrors

Pull the side mirrors in carefully
when driving through a narrow
space, like an automatic car wash.

SPEED CONTROL (IF EQUIPPED)

With speed control set, you can maintain a set speed without keeping
your foot on the accelerator pedal.

WARNING: Do not use the speed control in heavy traffic or on
roads that are winding, slippery or unpaved.

Using speed control

The speed controls are located on the steering wheel. The following
buttons work with speed control:

ON: Press to turn system on.

OFF: Press to turn system off.

RES (Resume): Press to resume a
set speed.

SET+: Press to set the speed or
increase the set speed.

CST- (Coast): Press to decrease
the set speed.

Setting speed control

1. Press and release ON.

2. Accelerate to the desired speed.

3. Press and release SET+.

4. Take your foot off the accelerator pedal.

5. The indicator light

on the instrument cluster will turn on.

Driver Controls

52

Note:
• Vehicle speed may vary momentarily when driving up and down a

steep hill.

• If the vehicle speed increases above the set speed on a downhill, you

may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below

your set speed on an uphill, your speed control will disengage.

Disengaging speed control

To disengage the speed control, press the brake pedal or the clutch
pedal (if equipped). Disengaging the speed control will not erase the
previous set speed.

Note: When you use the clutch pedal to disengage the speed control,
the engine speed may briefly increase, this is normal.

Resuming a set speed

Press and release RES. This will automatically return the vehicle to the
previously set speed.

Increasing speed while using speed control

To set a higher speed:
• Press and hold SET+ until you get to the desired speed, then release

the control. You can also use SET+ to operate the tap-up function.
Press and release SET+ to increase the set speed in 1 mph (1.6 km/h)
increments.

• Use the accelerator pedal to get to the desired speed. When the

vehicle reaches that speed, press and release SET +.

Reducing speed while using speed control

To reduce a set speed:
• Press and hold CST- until you get to the desired speed, then release

the control. You can also use CST- to operate the tap-down function.
Press and release the CST- to decrease the set speed in 1 mph
(1.6 km/h) increments.

• Press the brake pedal or the clutch pedal (if equipped) until the

desired vehicle speed is reached, then press and release SET+.

Turning off speed control

To turn off the speed control, press OFF or turn off the ignition.

Note: When you turn off the speed control or the ignition, your speed
control set speed memory is erased.

Driver Controls

53

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)

WARNING: Do not install additional floor mats on top of the
factory installed floor mats as they may interfere with the

accelerator or the brake pedals.

Position the floor mat so that the
eyelet is over the pointed end of the
retention post and rotate forward to
lock in. Make sure that the mat does
not interfere with the operation of
the accelerator or the brake pedal.
To remove the floor mat, reverse the
installation procedure.

BEDRAILS (IF EQUIPPED)
• This bedrail is for appearance use only.

WARNING: To help prevent injury, do not use bedrail to retain
cargo.

• Retain cargo with the pickup tiedown hooks.

Driver Controls

54