Ford Five Hundred (2007 year). Manual — part 24

Press

to automatically move the seat, mirrors and adjustable pedals to

the desired memory position (the positions correspond to the transmitter
being used). Note: You can associate a specific remote entry transmitter
to each memory position. For more information on programming the
transmitters to Driver 1 and Driver 2 memory positions respectively,
refer to How to reprogram your remote entry transmitters later in this
chapter.

Activating the memory seat feature

To activate this feature:

1. Position the seat, mirrors and adjustable pedals to the position
desired.

2. Press the SET control on the
driver’s door panel.

3. Within 5 five seconds, press the 1
or 2 control on the driver’s door
panel to which you would like to
associate with the seat, mirrors and
adjustable pedals and Driver 1 or
Driver 2 positions.

4. Repeat this procedure for the
other Driver position if desired.

Replacing the battery

The remote entry transmitter uses one coin type three-volt lithium
battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin between the two
halves of the remote entry
transmitter near the key ring. DO
NOT TAKE THE RUBBER COVER
AND CIRCUIT BOARD OFF THE
FRONT HOUSING OF THE
REMOTE ENTRY TRANSMITTER.

Locks and Security

98

2. Do not wipe off any grease on the
battery terminals on the back
surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when
disposing of transmitter batteries.

4. Insert the new battery. Refer to the diagram inside the remote entry
transmitter for the correct orientation of the battery. Press the battery
down to ensure that the battery is fully seated in the battery housing
cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause the remote transmitter
to become deprogrammed from your vehicle. The remote transmitter
should operate normally after battery replacement.

Replacing lost remote entry transmitters

If you would like to have your remote entry transmitter reprogrammed
because you lost one, or would like to buy additional remote entry
transmitters, you can either reprogram them yourself, or take all
remote entry transmitters to your authorized dealer for
reprogramming.

Note: If your vehicle is equipped with the memory seats/power
mirrors/adjustable pedals feature, you can associate a remote entry
transmitter to each memory position using this procedure. The first
transmitter that is programmed will recall Driver 1 settings, and the
second transmitter that is programmed will recall Driver 2 settings.

How to reprogram your remote entry transmitters

You must have all remote entry transmitters (maximum of four)
available before beginning this procedure.

Locks and Security

99

Note: Ensure the brake pedal is not
depressed during this sequence.

To reprogram the remote entry
transmitters:

1. Ensure the vehicle is electronically unlocked.

2. Put the key in the ignition.

3. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)
position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN)
position.

4. The doors will lock, then unlock, to confirm that the programming
mode has been activated.

5. Within 20 seconds press any button on the remote entry transmitter to
be programmed. Note: If more than 20 seconds have passed you will
need to start the procedure over again.

6. The doors will lock, then unlock, to confirm that each remote entry
transmitter has been programmed.

7. Repeat Step 5 to program each additional remote entry transmitter.
Note: The first remote transmitter programmed corresponds to Driver 1;
the second, Driver 2.

8. Turn the ignition to the 1 (LOCK) position after you have finished
programming all of the remote entry transmitters. Note: If any one of
the transmitters is not reprogrammed, it will be erased.

9. The doors will lock, then unlock, to confirm that the programming
mode has been exited.

Illuminated entry

The interior lamps illuminate when the remote entry system or the
keyless entry system keypad (if equipped) is used to unlock the door(s).

The illuminated entry system will turn off the interior lights if:
• the ignition is turned to the 3 (RUN) position, or
• the remote transmitter lock control is pressed, or
• after 25 seconds of illumination.

Locks and Security

100

The inside lights will not turn off if:
• they have been turned on with the dimmer control, or
• any door is open.

Perimeter lamps illuminated entry

With the remote entry system, the following items will illuminate when
the

(unlock) control on the transmitter is pressed:

• Head lamps

• Park lamps

• Tail lamps
The lamps will automatically turn off:
• if the ignition switch is turned to the 3 (RUN) position, or
• the

(lock) control is pressed, or

• after 25 seconds of illumination.
Note: On some vehicles, the perimeter lamps illuminated entry feature
will not activate in daylight conditions.

Deactivating/activating perimeter lamps illuminated entry
You may enable/disable this feature by having your vehicle serviced by
your authorized dealer.
You may also perform the following power door lock sequence to
enable/disable the perimeter lamps feature. Note: Before starting, ensure
the ignition is in the 1 (LOCK) position and all vehicle doors are closed.
You must complete Steps 1–5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, wait a
minimum of 30 seconds before beginning again.

1. Place the key in the ignition and
turn the ignition to the 3 (RUN)
position.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition from the 3
(RUN) position to the 1 (LOCK)
position.
4. Press the power door unlock control on the door panel three times.
5. Turn the ignition back to the 3 (RUN) position. The horn will chirp
one time to confirm programming mode has been entered and is active.

Locks and Security

101