Ford Falcon. Manual — part 6
100-01-4 Identification
Codes 100-01-4
DESCRIPTION AND OPERATION (Continued)
Body Style Code
BODY TYPE
CODE
XT Sedan
SW
XT Wagon
WA
Futura Sedan
SW
Futura Wagon
WA
XR Sedan
SW
XR Ute
CM
GT Sedan
SW
Fairmont Sedan
SW
Fairmont Wagon
WA
Fairmont Ghia Sedan
SW
Fairlane Ghia
LW
LTD
LW
XL Ute
CM
XLS Ute
CM
Model Code
Body Type
Body Style
Model Code
Sedan
XT
18333
Wagon
XT
18363
Sedan
Futura
18334
Wagon
Futura
18364
Sedan
XR
18335
Sedan
FMT
18332
Wagon
FMT
18332
Sedan
FMT Ghia
18338
Sedan
Fairlane Ghia
18349
Sedan
LTD
18346
Ute
XL Tray
45313
Ute
XL SSB
45373
Ute
XR Tray
45375
Ute
XLS Tray
45314
Ute
XLS SSB
45374
G86656 en
100-01-5 Identification
Codes 100-01-5
DESCRIPTION AND OPERATION (Continued)
Paint Colour and Code
with the Design Rules referred to on the compliance
label of the vehicle.
Colour
Code
Such Laws must be complied with at all times.
Winter White
A1
Failure to do so may result in Substantial Financial
Venom
VF
Penalties. Where State/Territory Laws differ from the
Ice Mint Silver
EI
repair manual procedures, the Laws MUST take
precedence.
Barossa Reb
B7
To ensure continuing compliance it is imperative that
Congo Green
DG
the engine/emission system is serviced according to
Silhouette
ST
the specified procedure. A typical compliance plate is
Blue Print
UU
shown below.
Narooma Blue
NR
Compliance Plate (engine bay)
Phantom
P3
Mercury Silver
M7
Blue Pearl
CP
Acid Rush
RH
Citric Acid
JA
Blood Orange
HO
Victorian Taxi Yellow
44
Taxi Orange
22
Trim Colour and Code
Colour
Code
Stone
S1
Warm Charcoal
B1
Vehicle Compliance (VC) Label
Australian Design Rules (A.D.R.) reuire vehicle
manufacturere to comply with specific requirements
regarding consumer, environment protection, and
safety devices. A compliance plate is fitted to the
vehicle and this contains codes which relate to
specific design rules in effect at the time of vehicle
manufacture.
Legiclation requires that no alteration be made to a
vehicle that would result in the vehicle not complying
G86657 en
100-01-6 Identification
Codes 100-01-6
DESCRIPTION AND OPERATION (Continued)
Compliance Plate (A-pillar)
Emission Decal
Emission Control Information Decal is affixed to the
underside of the bonnet. Should this decal become
mutilated or unreadable, a new decal must be
obtained and affixed to the vehicla. To ensure
contained compliance it is imperative that the engine
and emission system is serviced according to the
service procedures outlined in this manual.
Should it become necessary to replace a component
which affects vehicle emissions, it is mandatory that
the replacement part be of the same calibration as the
original part.
No circumstances would permit the disconnection,
alteration or modification of any emission related
component on vehicles marketed by Ford Sales
Company of Australia Limited, except in accordance
with the diagnostic, maintenance and repair
procedures specified in the Company’s service
materials.
Any person who removes, modifies or otherwise
renders ineffective any emission control components
fitted to a vehicle could be contravening the relevant
regulations and be guilty of an offence under the
regulations. Any person who owns and/or operates
such a vehicle could also be guilty of an offence
under the regulations.
G86657 en
100-02-1
Jacking and Lifting
100-02-1
SECTION : 100-02 Jacking and Lifting
VEHICLE APPLICATION : 2003.0 BA Falcon
CONTENTS
PAGE
DESCRIPTION AND OPERATION
Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..100-02-2
Jacking/Lifting Points - Sedan/Wagon . . . . . . . . . . . . . . . . . . . . .100-02-2
Jacking/Lifting Points - Ute . . . . . . . . . . . . . . . . . . . . . . . . ..100-02-2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст