Ford Falcon. Manual — part 306
412-02-28 Heating
and
Ventilation 412-02-28
REMOVAL AND INSTALLATION (Continued)
5. Maintain force on airmix shaft end and ensure
4. Unclip Harness and remove.
airmix door is depressed fully as shown in sketch
thus correctly aligning airmix door to shaft.
Installation
1. Refit components in reverse order.
Dual Zone Sub Harness
Filter and Cover Assembly — Mesh
Removal
(Standard Fitment)
1. Refer to HVAC Assembly removal procedure in
Removal
this section and follow steps 1 - 12 inclusive.
1. Refer to glove compartment removal procedure,
2. Disconnect harness connector from
Section 501-12 to gain access to Filter.
Actuator-Electric Airmix.
2. Slide Mesh Filter and Cover assembly to open
position (LH side).
3. Disconnect harness connector from HIM.
3. Pull out Filter-assembly.
Installation
1. Refit components in reverse order.
G34257 en
412-02-29 Heating
and
Ventilation 412-02-29
REMOVAL AND INSTALLATION (Continued)
Filter — Particle (Optional Fitment)
Vent Outlet Register — Outboard
Register
Removal
1. Refer glove compartment removal procedure,
Removal and Installation
Section 501-12 to gain access to Filter.
1. Peel off door seal over area covering end cap of
2. Slide Cover and Seal Assembly to open (LH side).
instrument panel.
2. Remove
end
cap.
3. Remove Cover & Seal Assembly.
3. Remove trim spear from instrument panel. Care
must be taken with trim removal or inboard
retainer clip will be broken.
4. Pull out Particle Filter.
4. Remove three screws/self tappers from registers.
Ease register on inboard top edge to dislodge clip
and remove register.
Installation
1. Refit components in reverse order.
5. Assemble in reverse order.
G73255 en
412-02-30 Heating
and
Ventilation 412-02-30
REMOVAL AND INSTALLATION (Continued)
Vent Outlet Register — Centre
Installation
Register
1. Position
Air
Register.
Removal
1. Remove Interior Command Centre and Remote
Key Receiver taking all precautions described in
section 413-08.
2. Remove wire harness from Air Register.
2. Tighten 3 X M5 screws to 1.5 Nm, top centre
screw first.
3. Remove 3 X M5 screws from Air Register.
3. Reposition wire harness to Air Register.
4. Remove
Air
Register.
4. Install the Remote Key Receiver and the ICC.
Refer to Section 413-08.
Vent Outlet Register — Floor Console
Register
Removal and Installation
1. Close flaps on register.
G73255 en
412-02-31 Heating
and
Ventilation 412-02-31
REMOVAL AND INSTALLATION (Continued)
2. Pry register out of lower retainer clips first, then
4. Invert console and ease rear section away from
top clips.
main body.
3. Remove register.
5. Remove eight retaining screws locating duct to
console.
4. On assembly of register, enter lower clips first and
roll register into place.
Floor Console Duct
Removal and Installation
The floor console duct is removed from the vehicle as
part of the floor console assembly. The duct can then
be separated form the console.
1. Remove floor console and duct assembly (Refer
to section 501-12).
2. Remove vent outlet floor console register (Refer
to procedure in this section).
3. Lift console lid and remove two rearmost screws.
6. Carefully spread console at front to allow duct
clearance over locating lugs. Spread rear of
console at rear and lift out duct.
7. To install, reverse the steps 1-6.
G73262 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст