Ford Falcon. Manual — part 390
419-07-9 Satellite
Navigation 419-07-9
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
F2
Yes
Measure the voltage AUO+, AUO-, MUTE.
Repair the audio system.
Are the connections and the continuity of the wiring harnesses
Repair navigation ECU.
and connectors between the navigation and the power amplifier
No
normal?
Inspect the wiring harnesses and connectors.
PINPOINT TEST G : THE SCREEN DOES NOT DISPLAY A MAP WHEN THE "I AGREE" BUTTON IS
PRESSED (ONLY THE "DISCCAUTION"SCREEN IS SHOWN)
Test Step
Result / Action to Take
G1
Yes
Apply the parking brake and turn the ignition switch to ACC or ON.
Replace the map disc.
Does the same caution screen appear even if actions have been
Repair the navigation ECU.
taken for the respective caution screen as described in the table
No
below?
Normal
PINPOINT TEST H : THE MAP SCREEN TURNS WHITE OR BLUE (THE SWITCHES AND THE
VEHICLE’S CURRENT POSITION MARK ARE NOT SHOWN)
Test Step
Result / Action to Take
H1
Yes
Does the map appear if the map display scale is set to the widest
Correct the vehicle’s current position and
range?
recheck.
No
Go to H2
H2
Yes
Using a soft cloth, wipe the map disc, and insert the disc in the player.
Determine that the condition is normal (the
Then, turn the ignition switch from OFF to ON.
cause was the dirty disc).
Is the system okay?
No
Replace the map disc.
Repair the navigation ECU.
PINPOINT TEST I : THE SCREEN DOES NOT CHANGE TO THE NIGHT SCREEN MODE
Test Step
Result / Action to Take
I1
Yes
Is the picture quality adjustment set to the Day Screen mode?
The Day Screen mode will not show the Night
Screen mode.
No
Go to I2
G88871 en
419-07-10 Satellite
Navigation 419-07-10
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
I2
Yes
Does the screens other than the navigation screen appear in the
Check the display.
night mode when the tailight switch is ON?
No
Go to I3
I3
Yes
Does it make a beep sound when each of the switches is pressed
Repair the navigation ECU.
on the navigation remote control?
No
Inspect the connections the continuity of the
wiring harnesses and connectors between the
navigation ECU and the CDU display.
Areas to inspect : Remote
PINPOINT TEST J : THE REMOTE CONTROL IS NON-OPERATIONAL (ONLY ON THE NAVIGATION
SCREEN)
Test Step
Result / Action to Take
J1
Yes
Areas to inspect : Remote
Repeair the navigation ECU.
Are the connections the continuity of the wiring harnesses and
No
connectors between the navigation ECU and the CDU display
Inspect the wiring harnesses and connectors.
normal?
PINPOINT TEST K : THE VEHICLE’S CURRENT POSITION MARK DEVIATES CONSIDERABLY
Test Step
Result / Action to Take
K1
Yes
Does the GPS mark appear on the screen?
Go to K2
No
Inspect the wiring harness and connectors.
K2
Yes
Does it occur in a particular location?
The current position mark could deviate in an
area in which the vehicle’s actual location is
difficult to determine.
(Immediately after leaving a parking area, etc.
Parallel running roads, high-rise roads, loop
roads, etc.)
No
Go to K3
K3
Yes
Is the system currently undergoing a distance correction? (Does
Wait and see until the correction is completed
the AUTO CORRECTION button appear green on the distance
(for 10km or more). The AUTO CORRECTION
correction screen?)
button will turn blue upon completing the
correction.
No
Go to K4
G88871 en
419-07-11 Satellite
Navigation 419-07-11
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
K4
Yes
Is SPD (vehicle speed) normal in the vehicle signal check of the
Go to K5
navigation check menu on the service check screen?
No
Inspect the wiring harnesses and connectors.
Areas to inspect: SPD
K5
Yes
Correct the current position. Drive the vehicle for a while with the
Okay.
GPS mark shown and observe the display for a while.
No
Repair the navigation ECU.
PINPOINT TEST L : THE GPS MARK DOES NOT APPEAR ON THE DISPLAY
Test Step
Result / Action to Take
L1
Yes
Move the vehicle to an area with an unobstructed view. (The signals
Go to L2
from the satellites cannot be received at times in an area that is
surrounded by buildings.)
No
Securely connect the GPS antenna. Repair any
Is the GPS antenna connected securely? Check whether the
abnormal conditions of the wiring harness.
wiring harness is being pinched or is kinked sharply.
L2
Yes
Are there any retrofit accessories such as theft-deterrent
Go to L3
devices?
No
Replace the GPS antenna.
Replace the navigation ECU.
L3
Yes
The GPS mark appears on the display when the power (including
The reception sensitivity of the GPS could be
backup power) to a retrofit accessory is turned OFF.
affected if a retrofit accessory that receives
Is the system okay?
radiowave signals is installed. In this case,
change the position in which the retrofit
accessory is installed.
No
Replace the GPS antenna.
Replace the navigation ECU.
NOTE: Use a ground plate if the GPS antenna is
mounted inside the vehicle. The reception sensitivity
of the GPS could become affected if a ground plate is
not used. In addition, the GPS reception sensitivity
could become affected if a film is affixed to the glass.
In that case, mount the GPS antenna on the outside
of the vehicle.
G88871 en
419-07-12 Satellite
Navigation 419-07-12
DIAGNOSIS AND TESTING (Continued)
PINPOINT TEST M : THERE IS NO VOICE GUIDANCE
Test Step
Result / Action to Take
M1
Yes
When the volume in the volume setting of the menu screen is
Voice guidance cannot be given in the cases
turned to maximum, is there a voice announcement that says
listed below. Check again.
"The guidance will be given at this volume"?
A destination has not been set.
The vehicle is not being driven along the route.
(The remaining distance does not appear at the
bottom left area of the current position screen.)
The "Guidance in other modes" has not been
set. (No voice guidance will be given at this time
on a screen other than the map screen.)
No
Go to M2
M2
Yes
Measure the voltage AUO+, AUO-.
Go to M3
Are the connections the continuity of the wiring harnesses and
No
connectors between the navigation ECU and the speaker wiring
Inspect the wiring harnesses and connectors.
harness normal?
M3
Yes
Does the sound of the audio unit (radio, CD, etc.) come out from
Repair the navigation ECU.
the speakers?
No
Inspect the Audio unit.
PINPOINT TEST N : THE VEHICLE’S CURRENT POSITION MARK TURNS ON ITS OWN (THE MAP
TURNS ON ITS OWN)
Test Step
Result / Action to Take
N1
Yes
Has the ignition switch been turned to ACC or IG when the
If the ignition switch is turned to ACC or IG while
vehicle is placed on a turntable?
the vehicle is turned around, the turning speed
at that time is stored in memory as a reference
value. With the vehicle stopped, turn the ignition
switch from OFF to ACC or IG and recheck the
condition.
No
Go to N2
N2
Yes
On the service check screen, does the vehicle signal of
Repair the navigation ECU.
navigation check show the SPD to be normal?
No
Inspect the wiring harnesses and connectors.
Areas to inspect: SPD
G88871 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст