Ford Falcon. Manual — part 372
417-01-27 Exterior
Lighting 417-01-27
DIAGNOSIS AND TESTING (Continued)
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
1
Circuit 10C (G-R)
0 voltage, less than 5 ohms between stop lamp
Stop lamp power input
and brake switch
2
Circuit 57D (B)
0 voltage, less than 5 ohms between stop lamp
Stop lamp ground
and chassis ground
Inspection and Verification
Visual Inspection Chart
Mechanical
Electrical
Brake switch
Junction Box (JB):
fuse 7 (15A)
Circuitry
Stop Lamp bulbs
Symptom Chart
Condition
Source
Action
Both stop lamps are inoperative
Junction Box (JB):
Go to PinPoint Test L
fuse 7 (15A)
Circuitry
Brake switch
One or more stop lamps are
Circuitry
Go to PinPoint Test M
inoperative
Stop Lamp bulbs
The stop lamps are continuously on
Circuitry
Go to PinPoint Test N
Brake switch
Pinpoint Tests
Both headlamps are inoperative
Possible causes:
Circuit 10AA (G-R) open or short to ground.
Brake switch C-191.
Circuit 10Y (G-R) open or short to ground .
PINPOINT TEST L : THE STOP LAMPS ARE INOPERATIVE
Test Step
Result / Action to Take
L1
CHECK THE BRAKE SWITCH INPUT VOLTAGE
Disconnect: brake switch C-191.
Yes
Go to L2.
Turn ON ignition.
No
Measure the voltage between the brake switch C-191, circuit 10AA
Repair circuit 10AA (G-R).
(G-R), harness side and ground.
Test the system for normal operation.
Is the voltage greater than 10 volts?
L2
CHECK THE CIRCUIT 10Y (G-R) FOR A SHORT TO
GROUND
Measure the resistance between the brake switch C191, circuit 10Y
Yes
(G-R), harness side and ground.
Repair circuit 10Y (G-R)
Test the system for normal operation.
Is the resistance less than 5 ohms?
No
Go to L3.
G86730 en
417-01-28 Exterior
Lighting 417-01-28
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
L3
CHECK CIRCUIT 10 (G-R) FOR AN OPEN
Disconnect: Inoperative tail lamp.
Yes
Perform the brake switch testing in Section
Measure the resistance between the brake switch C191, circuit 10Y
206-06.
(G-R), harness side and inoperative tail lamp (one of the following):
Test the system for normal operation.
SWB Left tail lamp C-78, circuit 10A (G-R), harness side
No
SWB Right tail lamp C-77, circuit 10B (G-R), harness side
Repair circuit 10 (G-R).
SWB High mount stop lamp C-39, circuit 10D (G-R),
Test the system for normal operation.
harness side
LWB High mount stop lamp C-39, circuit 10Z (G-R),
harness side
Wagon Left tail lamp C-44, circuit 10A (G-R), harness side
Wagon Right tail lamp C-45, circuit 10B (G-R), harness side
Wagon High mount stop lamp C-39, circuit 10 (G-R),
harness side
Ute non-SSB Left tail lamp C-707, circuit 10C (G-R),
harness side
Ute non-SSB Right tail lamp C-705, circuit 10A (G-R),
harness side
Ute SSB Left tail lamp C-708, circuit 10C (G-R), harness
side
Ute SSB Right tail lamp C-706, circuit 10A (G-R), harness
side
Is the resistance less than 5 ohms?
One or more stop lamps are inoperative
Possible causes:
Circuit 10 (G-R) open.
Circuit 57 (B) open.
G86730 en
417-01-29 Exterior
Lighting 417-01-29
DIAGNOSIS AND TESTING (Continued)
PINPOINT TEST M : ONE OR MORE STOP LAMPS ARE INOPERATIVE
Test Step
Result / Action to Take
M1
CHECK CIRCUIT 10 (G-R) FOR AN OPEN
Disconnect: Inoperative stop lamp.
Yes
Perform the brake switch testing in Section
Turn ON ignition.
206-06.
Test the system for normal operation.
Measure the voltage between the brake switch C-191, circuit 10AA
(G-R), harness side and inoperative tail lamp.
No
SWB LH tail lamp C-78, circuit 10A (G-R), harness side
Repair circuit 10 (G-R).
SWB RH tail lamp C-77, circuit 10B (G-R), harness side
Test the system for normal operation.
SWB High mount stop lamp C-39, circuit 10D (G-R),
harness side
LWB High mount stop lamp C-39, circuit 10Z (G-R),
harness side
Wagon LH tail lamp C-44, circuit 10A (G-R), harness side
Wagon RH tail lamp C-45, circuit 10B (G-R), harness side
Wagon High mount stop lamp C-39, circuit 10 (G-R),
harness side
Ute cab chassis LH tail lamp C-707, circuit 10C (G-R),
harness side
Ute cab chassis RH tail lamp C-705, circuit 10A (G-R),
harness side
Ute style side box LH tail lamp C-708, circuit 10C (G-R),
harness side
Ute style side box RH tail lamp C-706, circuit 10A (G-R),
harness side
Is the resistance less than 5 ohms?
The stop lamps are continuously on
Possible causes:
Brake switch C-191
Circuit 10 (G-R) short to power
PINPOINT TEST N : THE STOP LAMPS ARE CONTINUOUSLY ON
Test Step
Result / Action to Take
N1
CHECK THE CIRCUIT 10Y (G-R) FOR A SHORT TO
POWER
Disconnect: brake switch C-191.
Yes
Repair circuit 10 (G-R).
Are the stop lamps illuminated?
Test the system for normal operation.
No
Perform the brake switch testing in Section
206-06.
Test the system for normal operation.
G86731 en
417-01-30 Exterior
Lighting 417-01-30
DIAGNOSIS AND TESTING (Continued)
Fog Lamps
Connector Circuit Reference
C-163 Power Distribution Box (PDB)
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
1
Circuit 37H (Y)
Greater than 10 volts and 10,000 between fog
Battery to fog lamp relay
lamp relay and ground
2
Circuit 57AX (B)
0 volts, less than 5 ohms between fog lamp relay
Fog lamp relay ground
and ground
3
477 (SB)
0 volts, less than 5 ohms between fog lamp
Fog lamp switch to fog lamp relay switch and fog lamp relay
4
478A (BR-W)
0 volts, less than 5 ohms between fog lamp relay
Fog lamp relay to fog lamps
and fog lamps
C-360 LH Fog Lamp
G86731 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст