Ford Probe (1997 year). Manual — part 5
25
❑
Using the Automatic Memory Load feature
You can activate the
Auto Memory Load
feature by pressing and holding the “AUTO
PRESET” button
for approximately three
seconds
. Auto Memory Load sets all memory
buttons in AM, FM1 and FM2 sequentially by
seeking out the first five strong stations for
the respective band and storing them in
memory buttons 1-5. (FM2 will store the
second set of strong stations from the FM
band.)
With Auto Memory Store, you can continually
set strong stations into your memory buttons
without losing your existing memory presets,
which is especially helpful while traveling. Your
radio will automatically set your memory
buttons to the strong local stations so you don’t
have to continually manually tune to existing
stations.
Activate Auto Memory Store by pushing the
“AUTO PRESET” button once. Your radio will
set the first five strong stations of the band you
are in (AM, FM1 or FM2) into the memory
buttons. The display will show “AUTO,” then
run through the frequencies, stopping
momentarily on the stations being set into the
memory buttons. The radio is now in the
“AUTO” mode and the display will show
“AUTO” each time a preset is activated.
NOTE:
If there are fewer than five strong
stations in the frequency band, the
remaining unfilled buttons will store
the last strong station detected on the
band.
After all stations have been filled, the radio will
begin playing the station stored on memory
button 1.
26
To deactivate the Auto Memory Store mode and
return to the manually-set memory button
stations (or those stations set using Auto
Memory Load), simply push the “AUTO
PRESET” button. Display will show “AUTO”
then “OFF.” The next time Auto Memory Store
is activated on that band, the radio will store the
next set of five strong stations.
Using the “AUDIO” button to adjust the
tone balance and speaker output
❑
Increasing or decreasing bass response
Push the “AUDIO” button repeatedly until
the display reads “BASS.” Push the “+” side
of the “VOL” button to increase bass (more
“lows”), and push the “-” side to decrease
bass (less “lows”).
❑
Increasing or decreasing treble response
Push the “AUDIO” button repeatedly until
the display reads “TREB.” Push the “+” side
of the “VOL” button to increase treble (more
“highs”), and push the “-” side to decrease
treble (less “highs”).
❑
Adjusting speaker balance
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the “AUDIO” button
repeatedly until the display reads “BAL.”
Push the “+” side of the “VOL” button to
shift the sound to the right speakers, and
push the “-” side to shift the sound to the
left speakers.
27
❑
Adjusting speaker fader
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Push the “AUDIO” button
repeatedly until the display reads “FADE.”
Push the “+” side of the “VOL” button to
shift the sound to the front speakers, and
push the “-” side to shift the sound to the
rear speakers.
NOTE:
Illuminated bars in the display show
relative levels of bass and treble and
positions of speaker balance and fader
functions after adjustments are made,
then revert to volume level set.
Clock operation
When in the radio mode, push the “CLOCK”
button to switch from radio frequency to clock.
Only the clock numerals will be displayed in the
clock mode — there is no A.M./P.M. indication.
When in the clock mode, the time will be
displayed until the button is pushed again.
However, if you retune the radio while it is in
the clock mode, the new radio frequency will be
displayed for approximately ten seconds and
then change back to clock.
When in the CD mode, push the “CLOCK”
button to change the display from elapsed time
mode to track number mode to clock mode. If
the CD track selection is changed when you are
in the clock or elapsed time mode, the new track
number will be displayed for approximately ten
seconds and then revert back to the previous
mode.
28
To set the clock, simultaneously press the
“CLOCK” button and either the bottom (
b
) half
of the “SEEK” button to set hours, or the top
(
a
) half of the “SEEK” button to set minutes.
Using the Controls on Your New Compact
Disc Player
Your new Ford Compact Disc Player is capable
of playing 12 cm
or
8 cm discs, without an
adapter. The player operates when the power is
on and a disc is inserted (
label side up
). Handle
the disc by its edge only. (Be sure to read and
follow all of the care and cleaning instructions
under
How To Take Care of and Clean Your CD
Player and Discs
.)
NOTE:
If after you insert a disc, the disc is
ejected and “ERROR” begins scrolling
in the display, remove the disc and
reinsert it right side up (label side up).
The digital display on your CD player will
either show the track (selection) number or the
elapsed time. (The display mode can be selected
by pressing the “CLOCK” button.) Indicators for
play (
a
), stop (
X
) and compression on (“C”)
are also in the display. (These features are
described later.)
Once a disc is inserted, operation of the CD
player will override that of the radio.
NOTE:
The volume, bass, treble, balance and
fader controls on the radio are also
used with the CD player. Refer to
earlier operating instructions on these
controls.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст