Ford Escape (2018 year). Manual — part 49

System Limitations

WARNING

The collision warning system’s brake
support can only help reduce the
speed at which a collision occurs if

the driver applies the vehicle’s brakes. The
brake pedal must be pressed just like any
typical braking situation.

Due to the nature of radar technology,
there may be certain instances where
vehicles do not provide a collision warning.
These include:

•

Stationary vehicles or vehicles moving
below 6 mph (10 km/h).

•

Pedestrians or objects in the roadway.

•

Oncoming vehicles in the same lane.

•

Severe weather conditions (see
blocked sensor section).

•

Debris build-up on the grille near the
headlamps (see blocked sensor
section).

•

Small distance to vehicle ahead.

•

Steering wheel and pedal movements
are large (very active driving style).

If the front end of the vehicle is hit or
damaged, the radar sensing zone may be
altered causing missed or false collision
warnings. See your authorized dealer to
have your collision warning radar checked
for proper coverage and operation.

REAR UNDER FLOOR
STORAGE

Cargo Management System

(If

Equipped)

E142445

The system is located in the floor of the
cargo area. Lift the handle to open.

Adjustable Load Floor

(If Equipped)

E142446

Vehicles with the standard size spare tire
can adjust the load floor to two positions.
The front of the load floor can be placed
either on (for high position) or below (for
low position) the ledges behind the rear
seats. The rear of the load floor always sits
on the two small shelves located on the
liftgate trim.

LUGGAGE COVERS

WARNINGS

Make sure that the posts are properly
latched in mounting features. The
cover may cause injury in a sudden

stop or accident if it is not securely
installed.

Do not place any objects on the
cargo area shade. They may obstruct
your vision or strike occupants of

your vehicle in a sudden stop or crash.

Use the cargo shade to cover items in the
cargo area of your vehicle.

E142447

Insert the ends of the cargo shade into the
mounting features located behind the rear
seat on the rear trim panels to install the
cargo shade.

To operate the cargo shade:

1.

Pull the rear edge of the cargo shade
rearward.

2. Secure both ends of the support rod

into the retention slots located on the
rear quarter trim panels.

ROOF RACKS AND LOAD
CARRIERS

(If Equipped)

WARNING

When loading the roof racks, we
recommend you evenly distribute the
load, as well as maintain a low

center of gravity. Loaded vehicles, with
higher centers of gravity, may handle
differently than unloaded vehicles. Take
extra precautions, such as slower speeds
and increased stopping distance, when
driving a heavily loaded vehicle.

The maximum recommended load, evenly
distributed on the crossbars, is:
•

100 lb (45 kg) for vehicles without a
moonroof.

•

45 lb (20 kg) for vehicles with a
moonroof.

Note: Never place loads directly on the roof
panel.

For correct roof rack system function, you
must place loads directly on crossbars
affixed to the roof rack side rails. When
using the roof rack system, we recommend
you use Ford Genuine Accessory crossbars
designed specifically for your vehicle.

Make sure that you securely fasten the
load. Check the tightness of the load
before driving and at each fuel stop.

Adjusting the Crossbar

(If Equipped)

Note: For less wind noise and better
aerodynamics, only install the crossbars
when you need them for carrying cargo. If
you prefer to keep the crossbars installed,
the front crossbar has two positions. The
front position is quieter for wind noise. The
rear position may help to reduce wind noise
from an open moonroof. Follow the steps
to reposition or remove the front crossbar.
You can remove the rear crossbar fasteners
by unscrewing the assembly.

E142448

1.

Remove the crossbar thumbwheels at
both sides of the front crossbar by
turning them counterclockwise.

Note: If you cannot loosen the thumbwheel
with your hand, loosen the fastener head.
You can also use a small screwdriver or
similar tool to loosen the thumbwheel by
inserting the shaft between the two paddles
of the thumbwheel and rotating it loose.

2. Remove the crossbar by sliding the

ends off of the shoulder bolts in the
side rails.

3. Move the crossbar to the new side rail

position and slide the crossbar onto
the shoulder bolt at that position.

4. Replace and tighten the thumbwheels

at both sides of the crossbar by turning
them clockwise until tight. You can use
a small screwdriver or similar tool to
tighten if necessary.

Make sure to check that the thumbwheels
are tight each time you add or remove load
from the roof rack, and periodically while
traveling. Make sure that the load is secure
before traveling.

LOAD LIMIT

Vehicle Loading - with and
without a Trailer

This section guides you in the
proper loading of your vehicle,

trailer, or both. Keep your loaded
vehicle weight within its design
rating capability, with or without
a trailer. Properly loading your
vehicle provides maximum return
of vehicle design performance.
Before you load your vehicle,
become familiar with the
following terms for determining
your vehicle’s weight rating, with
or without a trailer, from the
vehicle’s Tire and Loading
Information label or Safety
Compliance Certification label.

Tire and Loading Label Information
Example:

E198719

Payload

E143816

PAYLOAD