Ford Super Duty (2017 year). Manual — part 100
E162804
Front passenger side (4x4)
Note: View shown from the rear of the
vehicle to clearly identify the jack point.
Place the jack directly under the axle.
E162805
Rear
Note: Jack at the specified locations to
avoid damage to the vehicle.
Jacking the Vehicle
E162811
1.
Turn the jack handle clockwise until
the wheel is completely off the ground
and high enough to install the spare
tire.
2. Remove the lug nuts with the lug
wrench.
3. Replace the flat tire with the spare tire,
making sure the valve stem is facing
outward for all front wheels and single
rear wheel vehicles. If you are replacing
an inboard rear tire on dual rear wheel
vehicles, the valve stem must be facing
outward. If you are replacing the
outboard wheel, the valve stem must
be facing inward. Reinstall the lug nuts
until the wheel is snug against the hub.
Do not fully tighten the lug nuts until
the wheel has been lowered.
4. Lower the wheel by turning the jack
handle counterclockwise.
5. Remove the jack and fully tighten the
lug nuts in the order shown. See
Technical Specifications (page 409).
6. Stow the flat tire. See Stowing the flat
or spare tire if the vehicle is equipped
with a spare tire carrier.
7.
Stow the jack, jack handle and lug
wrench. Make sure the jack is securely
fastened so it does not rattle when
driving.
403
8. Unblock the wheels.
E161441
1
3
4
2
7
6
5
8
8-lug nut torque sequence
1
2
3
4
5
6
7
8
9
10
E169375
10-lug nut torque sequence
E162820
When installing the wheel center
ornaments, make sure that the ornament
retention towers on the back side of the
ornament are aligned with the studs or lug
nuts. The retention towers are designed to
be installed over the studs or nuts and
retain to the flange on the lug nut.
E162821
If the ornament retention towers are
aligned between the studs or lug nuts, the
ornament is improperly installed. This
improper installation may appear and
sound correct, but will not keep the
ornament on the vehicle. Ornaments
improperly installed in this manner will fall
off or become loose with minimal force or
impact.
F-350 Dual Rear Wheel, F-450 and
F-550 Vehicles
E162812
404
1.
Slide the notched end of the jack
handle over the release valve and use
the handle to slide the jack under the
vehicle. Make sure the valve is closed
by turning it clockwise.
2. Position the jack according to the
following guides:
E162813
Front (4x2): F-350 dual rear wheel
Note: Place the jack directly under the
I-beam.
E162814
Front driver side (4x4): F-350 dual rear
wheel
Note: Make sure the jack fits onto the flat
area on the outboard side of the differential
housing.
E162815
Front passenger side (4x4): F-350 dual
rear wheel
Note: View shown from the rear of the
vehicle to clearly identify the jack point.
Note: Place the jack directly under the axle
and inboard of the radius arm so that the
jack clears the radius arm.
E162816
Front: F-450 and F-550
405
E162817
Rear: F-350 dual rear wheel
E162818
Rear: F-450 and F-550
Jacking the Vehicle
E162819
1.
Insert the jack handle into the pump
linkage.
2. Use an up-and-down motion with the
jack handle to raise the wheel
completely off the ground.
Note: Hydraulic jacks are equipped with a
pressure release valve that prevents lifting
loads which exceed the jack's rated
capacity.
3. Remove the lug nuts with the lug
wrench.
4. Replace the flat tire with the spare tire,
making sure the valve stem is facing
outward on all front an inboard rear
wheels. If you are replacing the
outboard wheel, the valve stem must
be facing inward. Reinstall the lug nuts
until the wheel is snug against the hub.
Do not fully tighten the lug nuts until
the wheel has been lowered.
5. Lower the wheel by slowly turning the
release valve counterclockwise.
Opening the release valve slowly will
provide a more controlled rate of
descent.
6. Remove the jack and fully tighten the
lug nuts in the order shown. See
Technical Specifications (page 409).
7.
Stow the flat tire. See Stowing the flat
or spare tire if the vehicle is equipped
with a spare tire carrier.
8. Stow the jack, jack handle and lug
wrench. Make sure the jack is securely
fastened so it does not rattle when
driving.
9. Unblock the wheels.
406
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст