Ford Aerostar (1997 year). Manual — part 8
29
Using the Controls on Your New Compact
Disc Player
Your new Ford Compact Disc Player is capable
of playing 12 cm
or
8 cm discs, without an
adapter. The player operates when the power is
on and a disc is inserted (
label side up
). Handle
the disc by its edge only. (Be sure to read and
follow all of the care and cleaning instructions
under
How To Take Care of and Clean Your CD
Player and Discs
.)
NOTE:
If after you insert a disc, the disc is
ejected and “ERROR” begins scrolling
in the display, remove the disc and
reinsert it right side up (label side up).
The digital display on your CD player will
either show the track (selection) number or the
elapsed time. (The display mode can be selected
by pressing the “CLOCK” button.) Indicators for
play (
a
), stop (
X
) and compression on (“C”)
are also in the display. (These features are
described later.)
Once a disc is inserted, operation of the CD
player will override that of the radio.
NOTE:
The volume, bass, treble, balance and
fader controls on the radio are also
used with the CD player. Refer to
earlier operating instructions about
these controls.
How to insert a disc and begin play
Insert one disc,
label side up
into the disc
opening. When inserted, the disc automatically
loads into the unit and play starts at the
beginning of the first track (selection).
When the disc reaches the end, the disc player
automatically returns to the beginning of the
disc and resumes playing.
30
NOTE:
Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
NOTE:
The CD player has heat protection
circuitry to protect the laser diode. If
the temperature of the player reaches
167˚F (75˚C), the heat detection circuit
will shut off the player and “TOO
HOT” will scroll in the display for
approximately five seconds (radio will
resume playing). When the temperature
returns to normal operating range, the
CD player will again be operational.
How to stop and restart the CD player
When a disc is loaded, the unit automatically
enters the play mode and the play indicator (
a
)
illuminates. To stop temporarily, press the
“PLAY/STOP” button or the “AM/FM” button.
The stop indicator (
X
) in the display illuminates
and operation returns to the radio mode. To
resume CD play, press the “PLAY/STOP”
button once again.
NOTE:
If the ignition key is turned OFF
during play and then is set to the ON
or ACCESSORY position, the CD
player will resume playing in the mode
it was in when ignition was turned off.
Using the “SEEK” feature
The “SEEK” feature allows you to quickly find a
particular selection on the disc.
Press the bottom (
b
) half of the “SEEK” button
once to repeat the current playing selection.
Press the top (
a
) half of the “SEEK” button to
advance to the next selection.
31
Pressing and holding the bottom (
b
) or top (
a
)
half of the “SEEK” button will scroll backward
and forward respectively through the tracks.
How to fast forward or reverse your CD
player
To quickly search for a particular point in a
selection, press the “FF” button (to fast forward)
or the “REV” button (to reverse). While either
button is pressed, the disc goes forward or
backward at two different speeds depending on
how long the button is held down. (Pressing
either button for more than three seconds will
speed up the process.) Release the button at the
desired point (found by watching the elapsed
playing time in the display or by listening to the
sound during fast forward or reverse). When
you have reached the beginning of track 1, the
CD player will begin playing.
When you have reached the end of the disc by
keeping the fast forward button pressed, the
display will show “END” and the player will go
into pause mode. Push the “PLAY/STOP”
button to begin playing the first track of the
disc, press the “REV” button to back up from
the end of the disc, or use the “SEEK” function
to locate a desired track.
Using the “SCAN” function
Press the “SCAN/TUNE” button to enter the
scan mode. Once in the scan mode, press the top
(
a
) or bottom (
b
) half of the “SEEK” button to
scan forward or reverse, respectively. The CD
player will begin scanning the disc, stopping on
each listenable track for approximately eight
seconds. This continues until you press the
“SCAN/TUNE” button a second time. While in
the scan mode, the display shows the current
sampled track number.
32
Special features of your CD player
❑
Compression
The compression feature will bring soft and
loud passages closer together for a more
consistent listening level.
To turn the compression on, press the
“COMP” button. When on, the compression
indicator (“C”) will appear in the display.
Press the button again to turn off.
❑
Automatic Disc Storage
If the disc is ejected from the CD player but
is not removed from the disc opening within
approximately 10 seconds, the player will
automatically reload the disc for storage,
unless the disc is automatically ejected due to
a “focus error” (disc inserted upside down).
In this case, the disc will not be automatically
reloaded.
How to eject the disc
Push the “EJECT” button to stop play, eject the
disc and resume radio operation of your audio
system.
NOTE:
You can eject the disc while the radio
power and/or ignition is on or off.
How To Take Care of and Clean Your CD
Player and Discs
To ensure the continued performance of your
Ford Compact Disc Player, carefully read the
following precautions:
❑
Always handle the disc by its edge. Never
touch the playing surface.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст