Ford F-250 Super Duty (1999 year). Manual — part 53

Waxing your vehicle

Wax when water stops beading on the surface. This could be every three
or four months, depending on operating conditions.

Use only carnauba or synthetic-based waxes. Use cleaning fluid or
alcohol with a clean cloth to remove any bugs before waxing vehicle. Use
tar remover to remove any tar spots.

Avoid getting wax on the windshield. If you have wax applied at a
commercial car wash, it is recommended that you clean the wiper blades and
windshield as described in Cleaning the wiper blades and windshield.

Repairing paint chips

Minor scratches or paint damage from road debris may be repaired with
the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), touch-up
paint (#ALBZ-19500–XXXXA), or aerosol paint spray (#ALAZ-19500–
XXXXA) from the Ford Car Care Chemicals line. Please note that the
part numbers (shown as XXXX above) will vary with your vehicle’s
specific coloring. Observe the application instructions on the products.

Remove particles such as bird droppings, tree sap, insect remains, tar
spots, road salt and industrial fallout immediately.

Cleaning the wheels

Wash with the same detergent as the body of your vehicle. Do not use
acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong
detergents. Never use abrasives that will damage the finish of special
wheel surfaces. Use a tar remover to remove grease and tar.

The brushes used in some automatic car washes may damage the finish
on your wheels. Before going to a car wash, find out if the brushes are
abrasive.

Cleaning the engine

Engines are more efficient when they are clean because grease and dirt
buildup keep the engine warmer than normal. When washing:
• Take care when using a power washer to clean the engine. The high

pressure fluid could penetrate the sealed parts and cause damage.

• Do not spray with cold water to avoid cracking the engine block or

other engine components.

• Never wash or rinse the engine while it is running; water in the

running engine may cause internal damage.

Maintenance and care

209

Cleaning plastic exterior parts

Use vinyl cleaner for routine cleaning. Clean with a tar remover if
necessary. Do not clean plastic parts with thinners, solvents or
petroleum-based cleaners.

Cleaning the exterior lamps

Wash with the same detergent as the exterior of your vehicle. Use glass
cleaner or tar remover if necessary.

To avoid scratching the lamps, do not use a dry paper towel, chemical
solvents or abrasive cleaners.

Cleaning the wiper blades and windshield

If the wiper blades do not wipe properly, clean the wiper blade rubber
element with undiluted windshield washer solution or a mild detergent.
To avoid damaging the blades, do not use fuel, kerosene, paint thinner or
other solvents.

If the wiper still does not wipe properly, this could be caused by
substances on the windshield such as tree sap and some hot wax
treatments used by commercial car washes. Clean the outside of the
windshield with a non-abrasive cleanser such as the non-abrasive
Bon-Ami

威 powder. Rinse thoroughly with clean water. Do not use

abrasive cleansers on glass as they may cause scratches. The windshield
is clean if beads do not form when you rinse it with water. The
windshield and wiper blades should be cleaned on a regular basis, and
blades or rubber elements replaced when worn.

Cleaning the instrument panel

Clean with a damp cloth, then dry with a dry cloth.

Avoid cleaner or polish that increases the gloss of the upper portion of
the instrument panel. The dull finish in this area helps protect the driver
from undesirable windshield reflection.

Cleaning the interior fabric

Remove dust and loose dirt with a whisk broom or a vacuum cleaner.
Remove fresh spots immediately. Do not use household or glass cleaners.
These agents can stain and discolor the fabric. Use a mild soap and
water solution if necessary.

Maintenance and care

210

Cleaning and maintaining the safety belts

Clean the safety belts with a mild soap solution recommended for
cleaning upholstery or carpets. Do not bleach or dye the belts, because
these actions may weaken the belt webbing.

Check the safety belt system periodically to make sure there are no
nicks, wear or cuts. If your vehicle has been involved in an accident,
refer to the Safety belt maintenance section in the Seating and safety
restraints chapter.

Cleaning leather seats (if equipped)

To clean, simply use a soft cloth dampened with water and a mild soap.
Wipe the leather again with a damp cloth to remove soap residue. Dry
with a soft cloth. For tougher soiling concerns, Ford recommends using
the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from
your Ford Dealer. This mild cleaner and special pad, cleans the leather
and maintains its natural beauty. Follow the instructions on the cleaner
label. Regular cleaning of your leather upholstery helps maintain its
resiliency and color.

Do not use household cleaning products, alcohol solutions,
solvents or cleaners intended for rubber, vinyl or plastics.

Maintenance and care

211

MOTORCRAFT PART NUMBERS

Component*

5.4L V8 engine

6.8L V10 engine

Air filter element

FA-1634

FA-1634

Fuel filter

FG-986B

FG-986B

Oil filter

FL-820-S

FL-820-S

PCV valve

EV-233

EV-233

Battery (Standard)

BXT-65-650

BXT-65-650

Battery (Optional)

BXT-65-750

BXT-65-650

Spark plugs-platinum**

AWSF-22E

AWSF-22E

**Refer to Vehicle Emissions Control Information (VECI) decal for spark
plug gap information.

REFILL CAPACITIES

Fluid

Ford Part Name

Application

Capacity

Front axle

Motorcraft SAE
75W90 Axle
Lubricant

F-250/350 Dana
50 axle

1.8L (3.8 pints)

F-350/450/550
Dana 60 axle

2.7L (5.8 pints)

Rear axle

1,2,3

Motorcraft SAE
75W140 Synthetic
Rear Axle Lubricant

F-250 /350
(10.50 inch
axle)

3.3L (6.9 pints)

Motorcraft SAE
75W90 Synthetic
Rear Axle Lubricant

F-350/450
Dana 80

3.9L (8.3 pints)

Motorcraft SAE
80W90 Premium
Rear Axle Lubricant

F-550 Dana 135

11.6L
(24.5 pints)

Brake fluid

High Performance
DOT 3 Motor
Vehicle Brake Fluid

All

Fill to line on
reservoir

Capacities and specifications

212