Ford Fiesta (2011 year). Manual — part 83
1. 12 volt battery.
2. Adapter box (AC).
3. Deployment lead (part of Test and
Deployment Lead, Air Bag/Pyrotechnic
Safety Belt).
4. Deployment lead (40-007-15 (part of Test
and Deployment Lead, Air Bag/Pyrotechnic
Safety Belt)).
E58700
1
2
4
3
6. Release the adapter box AC button.
TIE0024562
7. To deploy an air bag or safety belt
pretensioner, connect the deployment leads
to the RCM electrical connector.
• For the pin numbers, refer to the special tool
usage table below.
TIE0026423
G953458en
501-20B-
16
Supplemental Restraint System
501-20B-
16
GENERAL PROCEDURES
201
8. Move as far away as possible from the
vehicle and depress both switches to deploy
the air bag or safety belt pretensioner.
DTL4003010
9. To deploy the remaining air bags and safety
belt pretensioners, refer to the special tool
usage table below for the RCM electrical
connector pin numbers.
• Repeat steps six and seven.
Special Tool Usage
Black Deployment
Lead
Red Deployment
Lead
Electrical
connector
Description
Pin 4
Pin 3
A
Driver air bag module
Pin 7
Pin 8
A
Driver lower air bag module
Pin 10
Pin 9
A
Passenger air bag module
Pin 19
Pin 20
B
Side air bag module - driver side
Pin 8
Pin 7
B
Side air bag module - passenger
side
Pin 1
Pin 2
B
Safety belt retractor and preten-
sioner - driver side
Pin 4
Pin 3
B
Safety belt retractor and preten-
sioner - passenger side
Pin 9
Pin 10
B
Side air curtain - passenger side
Pin 18
Pin 17
B
Side air curtain - driver side
10. RCM electrical connectors.
G953458en
501-20B-
17
Supplemental Restraint System
501-20B-
17
GENERAL PROCEDURES
201
E58551
A
B
All air bag modules
1. Deployed air bag module(s) and safety belt
pretensioners should be sealed in suitable
bags and then disposed of in accordance
with local contaminated waste regulations.
2. NOTE: All unserviceable air bag modules
have been placed on the Mandatory Return
List. All discolored or damaged air bag
modules should be treated the same as any
unserviceable live air bag module being
returned.
If an air bag module or safety belt
pretensioner fails to deploy, remove the
component.
3.
WARNING: Under no circumstances is
an unserviceable air bag module or safety
belt pretensioner to be returned through the
local mailing system. Failure to follow this
instruction may result in personal injury.
If an air bag module or safety belt
pretensioner fails to deploy, seal the
unserviceable air bag module or safety belt
pretensioner in suitable packaging and
return to the Exchange Plan Center, as
appointed through the local National Sales
Company.
G953458en
501-20B-
18
Supplemental Restraint System
501-20B-
18
GENERAL PROCEDURES
201
Restraints Control Module (RCM)
General Equipment
Ford approved diagnostic tool
Removal
WARNINGS:
The supplemental restraint system (SRS)
is active for a certain length of time after
the power supply has been disconnected.
Wait for a minimum of 3 minutes before
disconnecting or removing any SRS
components.
Make sure that the vehicle electrical
system is fully depowered and no other
power source is connected.
Wear safety goggles.
NOTE: Removal steps in this procedure may
contain installation details.
1.
Refer to: Supplemental Restraint System (SRS)
Health and Safety Precautions
(100-00
General Information, Description and
Operation).
2.
Refer to: Battery Disconnect and Connect
(414-01 Battery, Mounting and Cables,
General Procedures).
3.
Refer to: Floor Console
(501-12 Instrument
Panel and Console, Removal and Installation).
4.
E104864
5. Torque: 10 Nm
E103432
x3
x3
Installation
1. To install, reverse the removal procedure.
2. When a new RCM is installed, configure the
RCM using the diagnostic tool.
General Equipment: Ford approved diagnostic
tool
G1087482en
501-20B-
19
Supplemental Restraint System
501-20B-
19
REMOVAL AND INSTALLATION
201
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст