Ford Police Interceptor Utility (2018 year). Manual — part 15

WINDSHIELD WIPERS

Note: Fully defrost the windshield before
you switch the windshield wipers on.

Note: Make sure you switch the windshield
wipers off before entering a car wash.

Note: If streaks or smears appear on the
windshield, clean the windshield and the
wiper blades. If that does not resolve the
issue, install new wiper blades.

Note: Do not operate the wipers on a dry
windshield. This may scratch the glass,
damage the wiper blades or cause the wiper
motor to burn out. Always use the
windshield washers before wiping a dry
windshield.

E208496

•

Rotate away from you for long wipe
interval.

•

Rotate toward you for short wipe
interval.

Speed Dependent Wipers

When your vehicle speed increases, the
interval between wipes decreases.

WINDSHIELD WASHERS

Note: Do not operate the wipers on a dry
windshield. This may scratch the glass,
damage the wiper blades or cause the wiper
motor to burn out. Always use the
windshield washer before wiping a dry
windshield.

Note: Do not operate the washers when
the washer reservoir is empty. This may
cause the washer pump to overheat.

E208497

•

A brief press causes a single wipe
without washer fluid.

•

A brief press and hold causes the
wipers to swipe three times with
washer fluid.

•

A long press and hold turns on the
wipers and washer fluid for up to 10
seconds.

A wipe occurs a few seconds after washing
to clear any remaining washer fluid. You
can switch this feature on or off in the
information display.

REAR WINDOW WIPER AND
WASHERS

Note: Make sure you switch the windshield
wipers off before entering a car wash.

Rear Window Wiper Blade

E208498

Intermittent wipe.

2

Low speed wipe.

1

Off.

0

Rear Window Washer

Rotate and hold the control to the top or
bottom position to switch on the rear
window washer. The control returns to the
2 or 0 position when you release it.

Rear Camera Washer

Switching on the rear washer also turns on
the rear camera washer.

GENERAL INFORMATION

Condensation in Lamp Assemblies

Exterior lamps have vents to
accommodate normal changes in air
pressure.

Condensation can be a natural by-product
of this design. When moist air enters the
lamp assembly through the vents, there is
a possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a fine mist
can form on the interior of the lens. The
fine mist eventually clears and exits
through the vents during normal operation.

Clearing time may take as long as 48 hours
under dry weather conditions.

Examples of acceptable condensation are:
•

The presence of a fine mist (no streaks,
drip marks or large droplets).

•

A fine mist covers less than 50% of the
lens.

Examples of unacceptable condensation
are:
•

A water puddle inside the lamp.

•

Streaks, drip marks or large droplets
present on the interior of the lens.

If you see any unacceptable condensation,
have your vehicle checked by an authorized
dealer.

Silent Mode

(If Equipped)

You can switch on Silent Mode in the
information display. See Information
Displays (page 79).

When you enable Silent Mode, the
following features may be disabled:
•

Welcome/farewell strategy.

•

Courtesy lighting and backlighting.

•

Daytime running lamps.

Note: In markets where daytime running
lamps are mandated by law, Silent Mode
will not disable the daytime running lamps.

LIGHTING CONTROL

E142449

Off.

A

Parking lamps, instrument panel
lamps, license plate lamps and
rear lamps.

B

Headlamps.

C

Headlamp High Beam

E167827

Push the lever away from you to switch
the high beam on.

Push the lever forward again or pull the
lever toward you to switch the high beams
off.

Headlamp Flasher

E163268

Slightly pull the lever toward you and
release it to flash the headlamps.

Spot Lamp Control

(If Equipped)

E203952

Use the switch on the chrome handle to
turn the spot lamp on and off.

Rotate and twist the handle to adjust the
position of the spot lamp.

AUTOLAMPS

(If Equipped)

WARNING

The system does not relieve you of
your responsibility to drive with due
care and attention. You may need to

override the system if it does not turn the
headlamps on in low visibility conditions,
for example daytime fog.

E142451

When the lighting control is in the
autolamps position, the headlamps turn
on in low light situations, or when the
wipers turn on.

The headlamps remain on for a period of
time after you switch the ignition off. Use
the information display controls to adjust
the period of time that the headlamps
remain on.

Note: If you switch the autolamps on, you
cannot switch the high beams on until the
system turns the low beams on.

Windshield Wiper Activated
Headlamps

When you switch the autolamps on, the
headlamps turn on within 10 seconds of
switching the wipers on. They turn off
approximately 60 seconds after you switch
the windshield wipers off.