Ford Edge (2018 year). Manual — part 12

GENERAL INFORMATION ON
RADIO FREQUENCIES

This device complies with Part 15 of the
FCC Rules and with Licence exempt RSS
Standards of Industry Canada. Operation
is subject to the following two conditions:
•

This device may not cause harmful
interference, and

•

This device must accept any
interference received, including
interference that may cause undesired
operation.

WARNING

Changes or modifications not
expressively approved by the party
responsible for compliance could

void the user's authority to operate the
equipment. The term "IC:" before the radio
certification number only signifies that
Industry Canada technical specifications
were met.

The typical operating range for your
transmitter is approximately 33 ft (10 m).
Vehicles equipped with the remote start
feature have a greater range.

One of the following could cause a
decrease in operating range:
•

Weather conditions.

•

Nearby radio towers.

•

Structures around your vehicle.

•

Other vehicles parked next to your
vehicle.

The radio frequency used by your remote
control can also be used by other radio
transmitters, for example amateur radios,
medical equipment, wireless headphones,
wireless remote controls, cell phones,
battery chargers and alarm systems. If the
frequencies are jammed, you will not be
able to use your remote control. You can
lock and unlock the doors with the key.

Note: Make sure to lock your vehicle before
leaving it unattended.

Note: If you are in range, the remote control
will operate if you press any button
unintentionally.

Note: The remote control contains sensitive
electrical components. Exposure to moisture
or impact may cause permanent damage.

Intelligent Access

The system uses a radio frequency signal
to communicate with your vehicle and
authorize your vehicle to unlock when one
of the following conditions are met:
•

You activate the front exterior door
handle switch.

•

You press the luggage compartment
button.

•

You press a button on the transmitter.

If excessive radio frequency interference
is present in the area or if the transmitter
battery is low, you may need to
mechanically unlock your door. You can
use the mechanical key blade in your
intelligent access key to open the driver
door in this situation. See Remote
Control (page 51).

REMOTE CONTROL

Intelligent Access Key

Note: You may not be able to shift out of
park (P) unless the intelligent access key is
inside your vehicle.

E253517

The intelligent access keys operate the
power locks and the remote start system.
The key must be in your vehicle to activate
the push-button start system.

Removable Key Blade

The intelligent access key also contains a
removable mechanical key blade that you
can use to unlock the driver door.

E254065

Push the release button and pull the key
blade out.

E151795

Note: Your vehicle keys came with a
security label that provides important key
cut information. Keep the label in a safe
place for future reference.

Replacing the Battery

Note: Refer to local regulations when
disposing of transmitter batteries.

Note: Do not wipe off any grease on the
battery terminals or on the back surface of
the circuit board.

Note: Replacing the battery does not delete
the transmitter programming to your vehicle.
The transmitter should operate normally
after you replace the battery.

A message appears in the information
display when the remote control battery
is low. See General Information (page
102).

Intelligent Access Key

The remote control uses one coin-type
three-volt lithium battery CR2032 or
equivalent.

E254065

1.

Push the release button and pull the
key blade out.

E218401

2. Twist a thin coin under the tab hidden

behind the key blade head to remove
the battery cover.

E218402

3. Insert a suitable tool, for example a

screwdriver, in the position shown and
carefully remove the battery.

4. Install new battery with the + facing

upward.

5. Reinstall the battery cover and the key

blade.

Using the Key Blade

The key cylinder is under a cap on the driver
door handle.

To remove the cap:

E151956

1.

Insert the key blade into the slot on the
bottom of the handle and press up.

2. While maintaining upward pressure,

move the cap rearward to release it.
Gently remove the key while doing so.

To install the cap:

E151957

1.

Place the cap just forward of the key
cylinder.

2. While applying pressure to the cap,

move it forward until it is in place. You
may hear a snap as it engages.

Make sure you have properly installed the
cap by trying to move it rearward.