Chery QQ6 (Body Accessories and Dimensions). Service Manual — part 11
161
Section 9 Rear Door Harness
I. Schematic Diagram of Harness
接室内线
束插件B
接室内
线束A
右后窗开关
右后扬声器
右后门锁
Rear Right Door Lock
Rear Right Window Switch
Rear Window Motor
Rear Right Speaker
To Interior Harness
Connector B
To Interior Harness
Connector A
-------------------------------------------------------------------------------------------------------------------------------------------------------------
162
II. Main Connectors Description
No
Connector Description
Number of Pin Connection
Remark
1
Connect to interior harness
connector B
8
Interior harness B
2
Right rear window switch
connector
10
Right Rear Window
Switch
3
Rear right door lock connector
4
Rear right door lock
4
Connect to interior harness
connector A
3
Interior harness A
5
Right rear speaker connector
2
Right rear speaker
6
Rear window motor connector
2
Rear window motor
-------------------------------------------------------------------------------------------------------------------------------------------------------------
163
III. Disassembly/Reassembly of Rear Left
Door Inner Harness
Part Number: S21-3724180
(I). Preparation
Tools:
socket wrench, cross screwdriver, flat head screwdriver
(II). Precautions
Power OFF before the electrical elements and
harnesses are removed.
The ignition switch must be in OFF state.
(III). Removal Procedure
1. Removal.
1.1. Remove the rear left door inner guard plate . (See
Disassembly/Reassembly of Door Inner Guard Plate)
1.2. Take off the rear left door inner protective film.
1.3. Pull out the lift motor connector.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
164
1.4. Pull out the door lock harness connector.
1.5. Pull out the Door Inner harness and vehicle
interior harness connectors.
1.6. Unclench the harness fixing clips.
1.8. Unclench the Door Inner harness rubber jacket.
1.9. Take off the harness assy. from the internal of
door.
2. Installation.
Install it in the reverse order of removal.
IV. Disassembly/Reassembly of Rear Right
Door Inner Harness
1. Removal.
Refer to Removal of Rear Left Door Inner Harness.
2. Installation.
Install it in the reverse order of removal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
165
Section 10 Back Door Harness
I. Schematic Diagram of Harness
后背门接
触开关
牌照灯
搭铁
高位制动灯
接后除霜正极线束
接室内线束
To Interior Harness
High-Mount Stop Lamp
To Rear Defroster Positive Harness
License Plate Lamp
Ground
Back Door Contact Switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
166
II. Main Connectors Description
No
Connector Description
Number
of Pin
Connection
Remark
1
Connect
to
interior
harness connector
6
Interior Harness
2
High-mount stop lamp
connector
1
High-mount stop lamp
3
Connect to rear defroster
positive harness connector
1
Rear defroster positive
harness
4
Back door harness ground
1
Body
At
back
door
paintwork
5
License
plate
lamp
connector
2
Side license plate lamp
6
Back door contact switch
connector
1
Back
door
contact
switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
167
III. Disassembly/Reassembly of Back Door
Inner Harness
Part Number: S21-3724160
(I). Preparation
Tools:
socket wrench, cross screwdriver, flat head screwdriver
(II). Precautions
DO NOT apply too big force when the harness is going
across the body paintwork hole so as to avoid the
harness breakage and short-circuit.
Power OFF before the electrical elements and
harnesses are removed.
The ignition switch must be in OFF state.
(III). Removal Procedure
1. Removal.
1.1.1.
Remove
the
C
pillar
trim.
(See
Disassembly/Reassembly of Ceiling)
1.1.2. Pull out the back door harness connector.
1.1.3. Remove the fix screws from the rear door
contact switch with a cross screwdriver.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
168
1.1.4. Pull out the connector of rear door contact
switch.
1.1.5. Remove the back Door Inner ornament plate.
(See Disassembly/Reassembly of Luggage Boot)
1.1.6. Pull out the connector of rear defroster positive
harness, and connector to the high-mount stop lamp
circuit.
1.1.7. Pull out the connector of high-mount stop lamp,
and then remove the harness from high-mount stop
lamp.
1.1.8. Pull out the connector to the license plate lamp.
1.1.9. Remove the grounding point from the back door
harness.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
169
1.1.10. Remove the fixing clips used to fasten the back
door harness.
1.1.11. Take off the back door inner harness.
2. Installation.
Install it in the reverse order of removal
, and implement
this installation with a special auxiliary tool (small
steel wire) and other tools.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
170
Section 11 Defroster Harness
I. Schematic Diagram of Defroster Positive Harness
II. Schematic Diagram of Defroster Negative Harness
III. Main Connectors Description
No
Connector Description
Number
of Pin
Connection
Remark
1
Defroster
positive
connector
1
Defroster positive
2
High-mount stop lamp
connector
1
High-mount stop
lamp
3
Back
door
harness
connector
1
Back door harness
4
Back
door
harness
connector
1
Back door harness
5
Defroster
negative
connector
1
Defroster negative
6
Body ground
Body
At the back door
To Defroster Positive
Ground
Defroster Negative
-------------------------------------------------------------------------------------------------------------------------------------------------------------
171
IV.
Disassembly/Reassembly
of
Rear
Defroster Harness
Defroster
harness
positive
(+),
part
number:
S21-3724530
Defroster
harness
negative
(-),
part
number:
S21-3724540
(I). Preparation
Tools:
socket wrench, cross screwdriver, flat head screwdriver
(II). Precautions
Power OFF before the electrical elements and
harnesses are removed.
The ignition switch must be in OFF state.
(III). Removal Procedure
1. Removal of Defroster Positive Harness
1.1.1、 Pull out the connector of rear defroster
positive harness, and the connector to the
high-mount
stop
lamp
circuit.
(See
Disassembly/Reassembly
of
Dack
Door
Harness)
1.1.2. Two connectors to back door harness. (Since the
circuit is a printed one, there is no actual harness.)
1.2 Installation
Install it in the reverse order of removal
2. Removal of Defroster Negative Harness
2.1.1. Remove the back door Inner ornament plate.
(See Disassembly/Reassembly of Luggage Boot)
2.1.2. Remove the defroster negative connector and
grounding point.
2.2 Installation
Install it in the reverse order of removal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст