Chery B14. Manual — part 4
S
ervice Manual for Chery V525 Car Chassis
4.7 Remove brake caliper assembly.
4.8 Removal of brake caliper assembly:
4.8.1 Remove guide bolt using 17# box end wrench.
Torque: 22-23N.m
4.8.2 Take out friction lining assembly.
4.8.3 Remove another guide bolt, separate brake cylinder.
4.8.4 Dismantle and overhaul brake cylinder (refer to the
methods for front wheel brake cylinder)
5. Assembly procedures
Refer to disassembly procedures.
S
ervice Manual for Chery V525 Car Chassis
Ⅳ.Adjustment and replacement of handbrake control cable
1. System structural diagram
1. Handle 2. Fixing bolt 3. Brake cable 4, 5. Right and left rear-wheel control cable
2. Preparation
Tools: flat-tip screwdriver, cross screwdriver, pincers, 10#, 16#, 18# sleeve, knock stick.
Accessories: none
3. Precautions
3.1 Wear necessary labor protection supplies to avoid accidents.
3.2 When carrying out disassembly and assembly of elastic element, make every effort to avoid
being injured.
3.3 Before carry out disassembly and assembly to exhaust pipe, in case of scald, the pipe
temperature must be dropped to room temperature.
4. Disassembly and assembly procedures
4.1. Disassembly of rear hand brake control cable
4.1.1 In accordance with disassembly and assembly method
of rear-wheel brakes, remove such assemblies as tire, brake
caliper, brake disk, etc. of rear wheel. Then completely
expose the hand brake assembly (take right rear wheel for
example).
Brake
T
o
ri
gh
t
re
a
r
b
ra
k
e
a
ss
e
m
b
ly
T
o
le
ft
r
ea
r
b
ra
k
e
a
ss
e
m
b
ly
S
ervice Manual for Chery V525 Car Chassis
4.1.2 Remove the return spring of hand brake shoes via
screwdriver.
4.1.3 Turn the guide pin of brake shoes to align the
spring seat via pliers, and then take out the guide pin.
4.1.4 Compress the return spring of control cable until
the control cable clip gets out of the guide pin of hand
brake.
4.1.5 Remove the fixing bolt that fastens control cable
and lower plate of hand brake assembly via 10# spanner.
Torque: 7-14N.m
4.1.6 Remove three fixing bolts that fasten hand brake
control cable and chassis via 10# sleeve.
Torque: 9-12N.m
S
ervice Manual for Chery V525 Car Chassis
4.1.7 Prize out the lifting eye of exhaust pipe via
screwdriver (it is unnecessary to remove the lifting eye
behind silencer).
4.1.8 Disconnect the connecting nut of exhaust pipe and
3-way catalytic converter via 18# sleeve, and then
remove the rear oxygen sensor (caution: along with the
descend of exhaust pipe, it may result in rupture of rear
oxygen sensor harness).
Torque: 60±5 N.m
4.1.9 Loosen the heat insulation fixing shims (6 pieces
total) of exhaust pipe via flat tip screwdriver, then
remove the heat insulation shim of exhaust pipe.
4.1.10 Detach the hand brake control cable of right-rear
wheel from the control cable branch joint by hand, the
right-rear wheel hand brake control cable then can be
removed.
4.2 Disassembly of hand brake control mechanism
and hand brake front control cable
4.2.1 Remove front-seat assembly using 16# sleeve.
Torque: 25±3N.m
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст