Chery Tiggo 5 (T21). Manual — part 213
18–
41
18
Ground Circuit Test
Ground Circuit
ET21180070
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
TCU
B
B
B
24
25
26
E-030
B
E-030
E-087
18–
42
18
DTC Confirmation Procedure:
Confirm that battery voltage is between 11 and 14 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC), and make it
communicate with vehicle electronic module by the data network.
Turn ignition switch to ON.
Using X-431 3G diagnostic tester to record and clear the DTCs stored in the TCU.
Turn ignition switch to LOCK and wait for a few seconds.
Turn ignition switch to ON, and then select "Read Code".
If DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent. Please refer to Intermittent
DTC Troubleshooting.
Diagnosis Procedure
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the TCU connector E-030.
c. Check for continuity between the terminals 24, 25 and 26
of connector E-030 and ground E-087.
1
Check ground for dirty or oxidized
Clean transmission ground contact point
NG
OK
2
Check ground circuit for continuity
-
+
RT21180880
E-030
E-087
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Repair or replace failed circuit
NG
OK
18–
43
18
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the TCU connector E-030.
c. Connect the negative battery cable.
d. Check if there is voltage between the terminals 24, 25
and 26 of TCU connector E-030 and ground.
3
Check if there is voltage in ground circuit
RT21180890
-
+
V
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Repair or replace failed circuit
NG
Replace TCU
OK
18–
44
18
DTC
P0705 Transmission Range Sensor 'A' Circuit (P-R-N-D-L Input)
ET21180080
TCU
7
49
4
3
2
8
1
B
18
BL
17
WR
16
Gr
14
Br
15
R
SEL_PWR_FB
SEL_POS_DS
SEL_POS_D
SEL_POS_N
REV_FB
SEL_POS_P
6
4
2
1
5
3
8
7
9
10
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
E-030
B
E-050
CONNECTOR A
E-050
B
E-030
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст