Chery Tiggo 5 (T21). Manual — part 89
06–
198
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Start the engine and warm it up to normal operating temperature, and then select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
DTC
P0012-00 "A" Camshaft Position - Timing Over-Retarded
DTC
P0015-00 "B" Camshaft Position - Timing Over-Retarded
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
P0012-00
"A" Camshaft Position -
Timing Over-Retarded
Ignition switch ON
Engine running
Camshaft phaser
Wire harness or connector
ECM
P0015-00
"B" Camshaft Position -
Timing Over-Retarded
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
OK
06–
199
06
a. Disconnect intake VVT control valve connector E-006.
b. Disconnect exhaust VVT control valve connector E-008.
c. Check VVT control valve connectors.
a. Check if intake/exhaust camshaft phaser is blocked or stuck.
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC P0012-00 or P0015-00 still exists.
2
Check VVT control valve connector
RT21070520
RT21070530
Repair or replace connector
NG
3
Check intake/exhaust camshaft phaser
OK
Replace intake/exhaust camshaft phaser
NG
4
Check for DTCs
OK
Replace ECM
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
06–
200
06
DTC
P0016-00
Crankshaft Position-Camshaft Position Correlation
Bank 1 Sensor A
DTC
P0018-00
Crankshaft Position-Camshaft Position Correlation
Bank 2 Sensor A
ET21065026
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
B
E-033
B
E-035
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1
2
3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4
5
6
7
8
9 10 11 12 13 14
1-34 1-29
1-31
1-41
2
3
1
LR
WR
Br
W
LR
LR
WR
Br
Br
W
CAMSHAFT
POSITION
SENSOR
(INTAKE)
CAMSHAFT
POSITION
SENSOR
(EXHAUST)
24
25
27
26
2
3
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
31
35
39
40
41
42
32
33
36
37
38 34
27
28
29
30
B
E-007
E-007
E-038
3
2
1
3
2
1
B
E-015
E-015
B
E-020
E-020
ECM-2
ECM-1
E-033
E-035
2-63
2-64
1-47
Br
Br
B
B
Br
B
1-48
E-026
E-028
1-32
1
WR
1-33
2
GW
WR
GW
ENGINE
SPEED
SENSOR
S
N
28
29
E-007
E-038
E-016
06–
201
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
P0016-00
Crankshaft Position-
Camshaft Position
Correlation Bank 1
Sensor A
Ignition switch ON
Engine running
Camshaft position sensor
Crankshaft position sensor
Wire harness or connector
Flywheel gear ring
Camshaft gear ring
ECM
P0018-00
Crankshaft Position-
Camshaft Position
Correlation Bank 2
Sensor A
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст