Chery Tiggo 5 (T21). Manual — part 373
33–
12
33
Removal
HINT:
Use the same procedures for the front passenger seat belt buckle assembly and driver seat belt buckle
assembly.
The procedures listed below are for the driver seat belt buckle assembly.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the front seat belt buckle assembly.
a. Using a screwdriver wrapped with protective tape, pry
the clip (1) on the wire harness connector.
b. Disconnect the front seat belt buckle connector
(arrow).
c. Remove the fixing nut (arrow) from front seat belt
buckle assembly.
(Tightening torque: 50 ± 5 N·m)
d. Remove the front seat belt buckle assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing front seat belt buckle
assembly.
DO NOT scratch the interior when removing front seat belt buckle assembly.
DO NOT damage the wire harness and connector when removing front seat belt buckle assembly.
RT21330080
1
RT21330090
CAUTION
Make sure to tighten all fixing nuts according to the specified torque when installing the front seat belt
buckle assembly.
Install the connector in place when installing the front seat belt buckle assembly.
33–
13
33
Height Adjuster Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the left B-pillar lower protector assembly (
).
4. Remove the left B-pillar upper protector assembly (
5. Remove the height adjuster assembly.
a. Remove the fixing bolt (arrow) from upper part of front
seat belt assembly.
(Tightening torque: 50 ± 5 N·m)
b. Remove the fixing bolt (arrow) from the height
adjuster assembly.
(Tightening torque: 23 ± 2 N·m)
c. Remove the height adjuster assembly in the direction
of arrow as shown in the illustration.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the height adjuster assembly.
DO NOT scratch the interior when removing the height adjuster assembly.
RT21330031
RT21330100
CAUTION
Make sure to tighten all fixing bolts according to the specified torque when installing the height adjuster
assembly.
33–
14
33
Rear Seat Belt Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the rear seat assembly (
4. Remove the rear left seat belt assembly.
a. Remove the fixing bolt (arrow) from the lower part of
rear seat belt assembly.
(Tightening torque: 50 ± 5 N·m)
b. Remove the left C-pillar lower protector assembly (
).
c. Remove the left C-pillar upper protector assembly (
d. Remove the fixing bolt (arrow) from the upper part of
rear seat belt assembly.
(Tightening torque: 50 ± 5 N·m)
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the rear seat belt assembly.
Appropriate force should be applied when removing the rear seat belt assembly, and avoid operating
roughly.
DO NOT scratch the interior when removing the rear seat belt assembly.
RT21330110
RT21330121
33–
15
33
e. Remove the fixing bolt (arrow) from the rear seat belt
retractor.
(Tightening torque: 50 ± 5 N·m)
f. Remove the fixing screw (1) from the rear seat belt
retractor.
(Tightening torque: 1.5 ± 0.5 N·m)
g. Remove the rear left seat belt assembly.
Inspection
Check the rear seat belt retractor.
HINT:
When inclination of rear seat belt retractor is 15° or less,
check that rear seat belt can be pulled out from rear seat belt
retractor. When the inclination of rear seat belt retractor is
over 45°, check that rear seat belt locks.
If result is not as specified, replace the rear seat belt
assembly.
Installation
Installation is in the reverse order of removal.
1
RT21330120
CAUTION
DO NOT disassemble the rear seat belt retractor.
Unlock
lock
45
o
Retractor
RT21330130
CAUTION
Keep seat belt assembly clean, avoid attaching oil and check seat belt assembly for damage when
installing the rear seat belt assembly.
Make sure to tighten all fixing bolts and fixing screws according to the specified torque when installing
rear seat belt assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст