Chery Tiggo 5 (T21). Manual — part 397
35–
63
35
a. Firmly reconnect all disconnected connectors.
b. Connect the negative battery cable.
c. Turn ignition switch to ON.
d. Use X-431 3G diagnostic tester (the latest software) to record and clear the DTCs stored in the Body
Control Module (BCM).
e. Turn ignition switch to LOCK and wait for a few seconds.
f. Turn ignition switch to ON.
g. Use X-431 3G diagnostic tester to read the DTCs in the Body Control Module (BCM) again.
5
Reconfirm DTCs
Result
Precede to
DTC B100813 and B100871 are output
NG
No DTC is output
OK
Replace Body Control Module (BCM)
NG
System is normal
OK
35–
64
35
ON-VEHICLE SERVICE
Headlight Adjustment Switch Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the driver airbag (
).
4. Remove the steering wheel assembly (
5. Remove the combination switch cover (
).
6. Remove the spiral cable (
7. Remove the headlight adjustment switch assembly.
a. Remove the headlight adjustment switch assembly
and wiper switch assembly wire harness connectors
(arrow).
b. Remove the combination switch assembly from steering column.
c. Press the claw (arrow) on wiper switch assembly, and
separates it from headlight adjustment switch
assembly.
d. Remove the headlight adjustment switch assembly.
RT21350060
RT21350070
35–
65
35
Inspection
1. Check headlight adjustment switch assembly.
a. Using ohm band of digital multimeter, check for
continuity between terminals as shown in the table.
Headlight Adjustment Switch Assembly (Position
Light/Low Beam Light/High Beam Light Switch)
If result is not as specified, replace headlight
adjustment switch assembly.
b. Using ohm band of digital multimeter, check for
continuity between terminals as shown in the table.
Headlight Adjustment Switch Assembly (Front Fog
Light/Rear Fog Light Switch)
If result is not as specified, replace headlight
adjustment switch assembly.
c. Using ohm band of digital multimeter, check for
continuity between terminals as shown in the table.
Headlight Adjustment Switch Assembly (Turn Signal
Light Switch)
If result is not as specified, replace headlight
adjustment switch assembly.
RT21350080
1 2
3 4
5
6 7 8 9 10
-
+
Multimeter
Connection
Switch
Condition
Specified
Condition
Terminal 2 -
Terminal 8
Switch OFF
No continuity
Terminal 2 -
Terminal 8
Switch in position
light
220 Ω
Terminal 2 -
Terminal 8
Switch in low
beam
150 Ω
Terminal 2 -
Terminal 9
Switch in high
beam
150 Ω
Terminal 2 -
Terminal 9
Switch in passing
light
330 Ω
RT21350080
1 2
3 4
5
6 7 8 9 10
-
+
Multimeter
Connection
Switch
Condition
Specified
Condition
Terminal 2 -
Terminal 5
Switch in front fog
light
Continuity
Terminal 2 -
Terminal 3
Switch in rear fog
light
Continuity
RT21350080
1 2
3 4
5
6 7 8 9 10
-
+
Multimeter
Connection
Switch
Condition
Specified
Condition
Terminal 2 -
Terminal 10
Switch in left turn
150 Ω
Terminal 2 -
Terminal 10
Switch in right
turn
330 Ω
35–
66
35
Installation
Installation is in the reverse order of removal.
CAUTION
Always install spiral cable correctly according to the specified operating instructions.
Check that the horn operates normally after installation.
Check SRS warning light after installation, and make sure that supplemental restraint system operates
normally.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст