Chery Tiggo 5 (T21). Manual — part 63
06–
94
06
a. Disconnect electronic throttle connector E-009.
b. Check electronic throttle connector.
a. Connect electronic throttle connector E-009.
b. Turn ignition switch to ON.
c. Using diagnostic tester, check throttle position sensor
signal voltage.
RT21060110
Repair or replace connector
NG
3
Check throttle position sensor signal voltage
OK
RT21060180
sensor voltage from throttle potentiometer 1
sensor voltage from throttle potentiometer 2
additive correction of the mixture adaptation
Voltage PWG potentiometer 1
Voltage PWG potentiometer 2
Doubled PWG potentiometer-2 voltage
multiplicative correction of the mixture adaptation
lambda controller output
Datastream name
Value
1.00
1.03
0.00
0.77
0.38
0.75
0.78
V
V
V
V
V
%
4.22
Unit
Datastream
Item
Condition
Standard Value
(V)
Throttle position
sensor 1
Accelerator pedal
released
0.78
Accelerator pedal
depressed
4.29
Throttle position
sensor 2
Accelerator pedal
released
4.22
Accelerator pedal
depressed
0.71
Go to step 7
OK
NG
06–
95
06
a. Turn ignition switch to LOCK.
b. Disconnect electronic throttle connector E-009.
c. Disconnect ECM connector E-035.
d. Check wire harness between connector terminals.
Check for Open
Check for Short
4
Check electronic throttle actuator circuit
E-035
E-009
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
1
2
3
4
5
6
-
+
RT21065037
Multimeter
Connection
Condition
Specified
Condition
E-035 (23) -
E-009 (1)
Always
Continuity
E-035 (11) -
E-009 (4)
Always
Continuity
Multimeter
Connection
Condition
Specified
Condition
E-035 (23) or
E-009 (1) - Body
ground
Always
No continuity
E-035 (23) or
E-009 (1) -
Battery positive
Always
No continuity
E-035 (11) or
E-009 (4) - Body
ground
Always
No continuity
E-035 (11) or
E-009 (4) -
Battery positive
Always
No continuity
Repair or replace related wire harness
NG
OK
06–
96
06
a. Check wire harness between connector terminals.
Check for Open
Check for Short
5
Check throttle position sensor circuit
E-035
E-009
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
1
2
3
4
5
6
-
+
RT21065038
Multimeter
Connection
Condition
Specified
Condition
E-035 (22) -
E-009 (2)
Always
Continuity
E-035 (14) -
E-009 (5)
Always
Continuity
E-035 (43) -
E-009 (3)
Always
Continuity
E-035 (13) -
E-009 (6)
Always
Continuity
Multimeter
Connection
Condition
Specified
Condition
E-035
(22, 14, 43, 13) or
E-009 (2, 5, 3, 6) -
Body ground
Always
No continuity
E-035
(22, 14, 43, 13) or
E-009 (2, 5, 3, 6) -
Battery positive
Always
No continuity
Replace wire harness or connector
(electronic throttle - ECM)
NG
OK
06–
97
06
a. Check electronic throttle for carbon deposits and foreign
matter accumulation inside.
b. Check if throttle valve body is stuck.
c. Check resistance of electronic throttle.
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC P1106-00, P1110-00, P1111-00, P1568-00 or P0606-00 still exists.
6
Check electronic throttle
RT21100211
1
2
3
4
5
6
-
+
Multimeter
Connection
Condition
Specified
Condition
Terminal 3 -
Terminal 2
At normal
temperature
1.067 kΩ
Terminal 6 -
Terminal 2
Throttle valve is
rotated
Resistance
increases as
throttle valve
opens
Terminal 6 -
Terminal 3
Resistance
decreases as
throttle valve
opens
Terminal 5 -
Terminal 2
Resistance
decreases as
throttle valve
opens
Terminal 5 -
Terminal 3
Resistance
increases as
throttle valve
opens
Clean or replace electronic throttle
assembly, and go to next step
NG
7
Check for DTCs
OK
Replace ECM
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст