Chery Tiggo 5 (T21). Manual — part 466
43–
44
43
ON-VEHICLE SERVICE
Power Glass Regulating Control Master Switch
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the power glass regulating control master switch assembly.
a. Remove the cushion rubber (1) from power glass
regulating control master switch assembly.
b. Remove the fixing screw (2) from power glass
regulating control master switch assembly.
(Tightening torque: 2 ± 0.5 N·m)
c. Using a screwdriver wrapped with protective tape, pry
up the power glass regulating control master switch
assembly.
d. Disconnect the connector (arrow) from power glass
regulating control master switch assembly, and
remove the power glass regulating control master
switch assembly.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing power glass regulating control
master switch.
Appropriate force should be applied when removing power glass regulating control master switch. Be
careful not to operate roughly.
Try to prevent front door protector assembly from being scratched when removing power glass regulating
control master switch.
RT21430050
1
2
RT21430060
RT21430070
43–
45
43
4. Remove the power glass regulating control master
switch.
a. Using a screwdriver wrapped with protective tape, pry
up the claws (arrow) on power glass regulating control
master switch, and remove the power glass regulating
control master switch.
Inspection
1. Check power glass regulating control master switch.
a. Using a digital multimeter, check for continuity of
power glass regulating control master switch
according to the table below.
If result is not as specified, replace power glass
regulating control master switch.
RT21430080
1
9
2 3 4 5 6 7 8
10111213141516
-
+
RT21430090
Area
Multimeter
Connection
Switch
Condition
Specified
Condition
Front left door
glass
regulating
switch
6 - 8
UP
220 Ω
OFF
No continuity
6 - 8
DOWN
Continuity
OFF
No continuity
Front right
door glass
regulating
switch
5 - 11
UP
220 Ω
OFF
No continuity
5 - 11
DOWN
Continuity
OFF
No continuity
Rear left door
glass
regulating
switch
4 - 11
UP
220 Ω
OFF
No continuity
4 - 11
DOWN
Continuity
OFF
No continuity
Rear right
door glass
regulating
switch
3 - 11
UP
220 Ω
OFF
No continuity
3 - 11
DOWN
Continuity
OFF
No continuity
43–
46
43
2. Check power glass regulating control master switch illumination.
a. Apply battery voltage to the terminals of power glass
regulating control master switch connector, and check
the operation of power glass regulating control master
switch according to the table below.
If result is not as specified, replace power glass
regulating control master switch.
Installation
Installation is in the reverse order of removal.
1
9
2 3 4 5 6 7 8
10111213141516
RT21430091
-
+
Measurement Condition
Specified
Condition
Battery positive
(+)
Battery negative
(-)
13
12
LED comes on
CAUTION
Check if connector is correctly installed when installing power glass regulating control master switch.
Check if switch operates normally after installing glass regulating control master switch.
43–
47
43
Front Door Outer Weather bar
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the outside rear view mirror assembly (
).
4. Remove the front left door outer weather bar.
a. Remove the front left door frame weatherstrip.
HINT:
It is not necessary to remove the front left door frame weatherstrip completely. There is a fixing screw in
the front door frame weatherstrip.
b. Remove 2 fixing screws (arrow) from front door outer
weather bar.
(Tightening torque: 1.3 ± 0.2 N·m)
c. Remove the front left door outer weather bar in the
direction of arrow as shown in the illustration.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing front door outer weather bar.
Appropriate force should be applied when removing front door outer weather bar. Be careful not to
operate roughly.
Try to prevent body paint surface from being scratched when removing front door outer weather bar.
RT21430160
RT21430170
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст