Chery Tiggo 5 (T21). Manual — part 510
47–
56
47
Back Door Opener Switch Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the back door protector assembly (
).
4. Remove the back door upper trim board assembly (
).
5. Remove the back door opener switch assembly.
a. Disconnect the back door opener switch connector
(arrow).
b. Remove 2 fixing bolts from the back door opener
switch assembly, and remove the back door opener
switch assembly.
(Tightening torque: 10 ± 1 N·m)
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing back door opener switch
assembly.
Try to prevent body paint surface from being scratched when removing back door opener switch
assembly.
RT21370261
RT21370300
CAUTION
Make sure damaged clips are replaced and back door opener switch assembly is installed in place when
installing back door opener switch assembly.
Install connector in place when installing back door opener switch assembly.
Make sure each function can operate properly after installing back door opener switch assembly.
47–
57
47
Back Door Air Spring Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the back door left air spring assembly.
a. Using a screwdriver wrapped with protective tape, pry
off the back door air spring upper clip.
b. Using a screwdriver wrapped with protective tape, pry
off the back door air spring lower clip and remove the
back door left air spring assembly.
4. Remove the back door air spring ball pin (arrow).
(Tightening torque: 10 ± 1 N·m)
WARNING
When removing back door air spring assembly, an assistant is needed to hold back door. Prevent back
door from dropping or sudden closing to cause accidents during operation.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing back door air spring assembly.
Try to prevent body paint surface from being scratched when removing back door air spring assembly.
When installing back door air spring assembly, prevent back door from dropping to damage body during
operation.
RT21470820
RT21470830
47–
58
47
Installation
Installation is in the reverse order of removal.
WARNING
When removing back door air spring assembly, an assistant is needed to hold back door. Prevent back
door from dropping or sudden closing to cause accidents during operation.
CAUTION
Try to prevent body paint surface from being scratched when installing back door air spring assembly.
Make sure back door air spring and back door air spring assembly clip are fitted closely after installing
back door air spring assembly.
1
48
EXTERIOR
Description 48-3
Specifications 48-6
Tool 48-7
Removal 48-8
Installation 48-9
Removal 48-10
Installation 48-10
Removal 48-11
Disassembly 48-12
Assembly 48-14
Installation 48-15
Front Bumper Stiffener Bracket
Removal 48-16
Installation 48-16
Removal 48-17
Installation 48-18
Removal 48-19
Installation 48-19
Removal 48-20
Installation 48-21
Removal 48-22
Installation 48-23
Removal 48-24
Installation 48-24
Engine Lower Protector Assembly
Removal 48-29
Installation 48-29
Removal 48-30
Disassembly 48-32
Assembly 48-33
Installation 48-33
Removal 48-34
Installation 48-34
Removal 48-35
Installation 48-36
Removal 48-37
Installation 48-37
Removal 48-38
Installation 48-38
Front Windshield Lower Garnish
Removal 48-39
Installation 48-40
Removal 48-41
Installation 48-42
Removal 48-43
Installation 48-44
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст