Chery Tiggo 5 (T21). Manual — part 75
06–
142
06
a. Unplug ECM fuse EF19 (10 A) from engine compartment fuse and relay box.
b. Check resistance of fuse EF19.
Standard resistance: less than 1 Ω
a. Disconnect engine compartment fuse and relay box
connector E-076.
b. Check wire harness between connector terminals.
Check for Open
Check for Short
6
Check ECM fuse
Replace ECM fuse
NG
7
Check wire harness and connector (ECM - engine compartment fuse and relay box)
OK
E-076
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
-
+
RT21065053
Multimeter Connection
Specified
Condition
E-033 (20) - E-076 (A2)
Continuity
Multimeter Connection
Specified
Condition
E-033 (20) or E-076 (A2) -
Body ground
No continuity
E-033 (20) or E-076 (A2) -
Battery positive
No continuity
Repair or replace wire harness or
connector
NG
Repair or replace engine compartment fuse and relay box or wire harness (engine compartment fuse
and relay box - battery)
OK
06–
143
06
a. Connect engine compartment fuse and relay box
connector E-076.
b. Turn ignition switch to ON.
c. Check voltage between terminals of ECM connector
E-033.
a. Unplug fuse EF17 (10 A) from engine compartment fuse and relay box.
b. Check resistance of fuse EF17.
Standard resistance: less than 1 Ω
8
Check ECM power supply voltage (ignition switch voltage)
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065054
Multimeter
Connection
Condition
Specified
Condition
E-033 (35) -
E-033 (63) or
E-033 (64)
Ignition switch ON
11 to 14 V
Go to step 12
OK
9
Check ECM fuse
NG
Replace fuse
NG
10
Check wire harness and connector (ECM - engine compartment fuse and relay box)
OK
06–
144
06
a. Disconnect engine compartment fuse and relay box
connector E-076.
b. Check wire harness between ECM connector terminals
and engine compartment fuse and relay box connector
terminals.
Check for Open
Check for Short
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC P0560-00, P0562-00 or P0563-00 still exists.
E-076
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
-
+
RT21065055
Multimeter Connection
Specified
Condition
E-033 (35) - E-076 (A4)
Continuity
Multimeter Connection
Specified
Condition
E-033 (35) or E-076 (A4) -
Body ground
No continuity
E-033 (35) or E-076 (A4) -
Battery positive
No continuity
Repair or replace wire harness or
connector
NG
11
Check ignition switch assembly (
)
OK
Replace ignition switch assembly
NG
Repair or replace engine compartment fuse and relay box or wire harness (engine compartment fuse
and relay box - ignition switch)
12
Check for DTCs
OK
Replace ECM
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
06–
145
06
DTC
P0627-00 Fuel Pump "A" Control Circuit/Open
DTC
P0628-00 Fuel Pump "A" Control Circuit Low
DTC
P0629-00 Fuel Pump "A" Control Circuit High
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст