Chery Tiggo 5 (T21). Manual — part 490
46–
10
46
Tool
General Tool
Digital Multimeter
RCH0000002
46–
11
46
Circuit Diagram
Seat System
ET21460010
RF02
20A
F2
F7
RF07
20A
INSTRUMENT
PANEL FUSE
AND RELAY
BOX B
B
YR
YR
GR
RW
Lg
Lg
RW
RW
R
R
R
RW
B
B
B
1
2
3
2
4
1
3
2
4
1
FRONT
PASSENGER
SEAT HEATER
SWITCH
BCM
1
2
A23
B1
FRONT
PASSENGER
SEAT HEATER
DRIVER
SEAT
HEATER
DRIVER
SEAT HEAT
SWITCH
B-042
I-047
IGNITION SWITCH
ON OR START
F1 F2 F3
F8 F9 F10
F11 F12 F13 F14
F15 F16 F17 F18
F4
F5 F6
F7
W
B-060
B-060
18
I-035
B-059
I-006
B-003
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18
W
B-059
1
2
3
4
5
6
7
8
B
B
I-044
1
2
3
4
5
6
7
8
I-044
B-065
B-071
B-067
B-067
ILLUMINTION
A32
A31
A30
A29
A28
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A27
A26
A25
A24
A23
A22
A21
A20
A19
A18
A17
B-065
B
L
I-005
I-005
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16
B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32
L
B-047
B-047
1
2
4
3
1
2
4
3
B-071
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
W
I-006
20
46–
12
46
ON-VEHICLE SERVICE
Front Seat Assembly
Removal
HINT:
Use the same procedures for the front passenger seat assembly and driver seat assembly.
Procedures listed below are for the driver seat assembly.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the driver seat headrest assembly.
a. As shown in the illustration, press the seat headrest
guide w/ button and remove the driver seat headrest
assembly.
4. Remove the driver seat assembly.
a. As shown in the illustration, pull up the seat track
unlock handle and move the seat assembly to the
rearmost position.
b. Using a screwdriver wrapped with protective tape, pry
up the seat front mounting foot cover.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing seat assembly.
Avoid scratch or damage to the body paint surface and carpet when removing seat assembly.
RT21460040
RT21460050
RT21460060
46–
13
46
c. Remove 2 fixing bolts (arrow) on the front side of seat
assembly.
(Tightening torque: 50 ± 5 N·m)
d. As shown in the illustration, pull up the seat track
unlock handle and move the seat assembly to the
foremost position.
e. Using a screwdriver wrapped with protective tape, pry
up the seat rear mounting foot cover.
f. Remove 2 fixing bolts (arrow) on the rear side of seat
assembly.
(Tightening torque: 50 ± 5 N·m)
RT21460070
RT21460071
RT21460080
RT21460090
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст