Chery Tiggo 5 (T21). Manual — part 176

15–

39

15

Check for Open

Check for Short

2

Check instrument panel wire harness and connector

-

+

RT21150290

J201

J202

J203

J204

J205

J206

J207

J208

J209

J210

J211

J212

J213

J214

J215

J216

I-030

4

3

2

1

8

7

6

5

I-017

Multimeter

Connection

Condition

Specified

Condition

I-030 (J211) -

I-017 (1)

Always

Continuity

I-030 (J210) -

I-017 (2)

Always

Continuity

I-030 (J213) -

I-017 (3)

Always

Continuity

I-030 (J204) -

I-017 (4)

Always

Continuity

I-030 (J203) -

I-017 (5)

Always

Continuity

I-030 (J205) -

I-017 (8)

Always

Continuity

Multimeter

Connection

Condition

Specified

Condition

I-030 (J211) or

I-017 (1) - Body

ground/Battery

positive

Always

No continuity

I-030 (J210) or

I-017 (2) - Body

ground/Battery

positive

Always

No continuity

I-030 (J213) or

I-017 (3) - Body

ground/Battery

positive

Always

No continuity

I-030 (J204) or

I-017 (4) - Body

ground/Battery

positive

Always

No continuity

I-030 (J203) or

I-017 (5) - Body

ground/Battery

positive

Always

No continuity

I-030 (J205) or

I-017 (8) - Body

ground/Battery

positive

Always

No continuity

Repair or replace instrument panel wire
harness and connector

NG

15–

40

15

a. Remove the engine switch (

See page 15-69

).

b. Check the engine switch (

See page 15-70

).

a. Connect related wire harness connectors.
b. Connect the negative battery cable.
c. Turn ignition switch ON.
d. Connect X-431 3G diagnostic tester to Data Link Connector (DLC) to check if any DTC is detected.

3

Check engine switch

OK

Repair or replace engine switch

NG

4

Confirm DTCs

OK

Repair or replace PEPS controller

NG

OK

System operates normally

15–

41

15

DTC

B1507-00 Abnormality in IG Circuit No Subtype Information

DTC

B1508-00 Abnormality in ACC Circuit No Subtype Information

ET21140030

B

BW

BG

R

RL

BATTERY

IGN2
RELAY
ERLY7

85

30

86

F4

F5

J104

B1

87

EF15

15A

ENGINE
COMPARTMENT
FUSE AND
RELAY BOX

E-065

E-067

E-069

E-073

E-074

IGNITION
SWITCH

LOCK

AM1

240W 120W

120W 120W

IG1 ACC AM2 IG2 ST2

ACC

ON

START

PEPS (J1)

I-029

I-013

J101

J102

J103

J104

J105

J106

J107

J108

J109

J110

J111

J112

J113

J114

J115

J116

Gr

I-029

E-078

10

11

B

W

W

R

RY

ACC
RELAY
ERLY13

85

30

86

F18

F17

J103

I2

87

EF48

20A

E-078

8

4

B

R

R

RW

RW

IGN1
RELAY
ERLY10

85

30

86

H6

H7

J102

K1

3

5

2

87

EF43

20A

E-078

7

9

E-071

I-004

B

E-071

1

2

3

4

5

6

7

8

9 10

11 12 13 14

3

2

1

6

5

4

Lg

I-013

B

E-065

Gr

E-074

W

E-067

W

E-069

Y

E-073

B1

B2

B3

B4

B5

B6

B7

B8 B9 B10

K2 K1

I2

I1

H8

H16

H7

H15

H6

H14

H5

H13

H4

H12

H3

H11

H2

H10

H1

H9

F12

F24

F11

F23

F10

F22

F9

F21

F8

F20

F7

F19

F6

F18

F5

F17

F4

F16

F3

F15

F2

F14

F1

F13

15–

42

15

DTC Confirmation Procedure

Confirm that battery voltage is normal before performing the following procedures.
 Turn ignition switch to LOCK.
 Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
 Turn ignition switch ON.
 Use X-431 3G diagnostic tester to record and clear the DTCs stored in the PEPS system.
 Turn ignition switch to LOCK and wait for a few seconds.
 Use X-431 3G diagnostic tester to select "Read Code".
 If DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
 If DTC is not detected, the malfunction indicated by the DTC is intermittent (

See page 15-19

).

Diagnosis Procedure

a. Turn off all the electrical equipment and ignition switch.
b. Disconnect the negative battery cable.
c. Remove the fuses EF15 (15 A), EF48 (20 A) and EF43 (20 A) from engine compartment fuse and relay

box.

d. Remove the IGN1 relay, IGN2 relay and ACC relay from engine compartment fuse and relay box.
e. Check if fuses and relays are blown or damaged.

a. Check engine compartment fuse and relay box ground E-078 (

See page 51-42

).

DTC Code

DTC Definition

DTC Detection

Condition

Possible Cause

B1507-00

Abnormality in IG
Circuit No Subtype
Information

Engine switch ON

 Wire harness or connector damaged
 Fuse
 IGN1 relay
 IGN2 relay
 ACC relay
 Engine switch
 Passive Entry & Passive Start (PEPS)

controller

B1508-00

Abnormality in ACC
Circuit No Subtype
Information

CAUTION

 When performing electrical equipment diagnosis and test, always refer to the circuit diagram for related

circuit and component information.

1

Check fuse and relay

Repair or replace damaged fuses and
relays.

NG

2

Check engine compartment fuse and relay box ground

OK