Chery Tiggo 5 (T21). Manual — part 86
06–
186
06
DTC
U0167-87 Lost Communication With IMMO
ET21065024
2-1
2-17
8
CAN H1
CAN L1
CAN H1
CAN L1
6
OB
O
OB
O
ECM-2
ECM-1
E-033
E-035
2-63
2-64
1-47
Br
Br
B
B
Br
B
1-48
E-026
E-028
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
B
E-033
B
E-035
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1
2
3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4
5
6
7
8
9 10 11 12 13 14
E-027
I-034
9
10
1
2
3
4
5
6
7
8
9 10
11
12
13
14 15
W
E-027
IMMOBILIZER
CONTROL
MODULE
I-018
7
5
3
1
8
6
4
2
B
I-018
06–
187
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
a. Disconnect ECM connector E-033.
b. Disconnect engine immobilizer module connector I-018.
c. Check if connectors are normal.
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
U0167-87
Lost Communication
With IMMO
Ignition switch ON
CAN line or connector
ECM
Engine immobilizer module
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
2
Check ECM connector and engine immobilizer module connector
OK
Repair or replace connectors
NG
OK
06–
188
06
a. Check CAN line.
Check for Open
Check for Short
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC U0167-87 still exists.
3
Check CAN line (ECM - engine immobilizer module)
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
7
5
3
1
8
6
4
2
I-018
-
+
RT21065068
Multimeter Connection
Specified
Condition
E-033 (1) - I-018 (8)
Continuity
E-033 (17) - I-018 (6)
Continuity
Multimeter Connection
Specified
Condition
E-033 (1) or I-018 (8) - Body ground
No continuity
E-033 (1) or I-018 (8) - Battery positive
No continuity
E-033 (17) or I-018 (6) - Body ground
No continuity
E-033 (17) or I-018 (6) - Battery
positive
No continuity
Repair or replace CAN line
NG
4
Replace ECM, and check for DTCs
OK
Replace engine immobilizer module
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
06–
189
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Start the engine and warm it up to normal operating temperature, and then select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
DTC
P000A-00 "A" Camshaft Position Slow Response
DTC
P000B-00 "B" Camshaft Position Slow Response
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
P000A-00
"A" Camshaft Position
Slow Response
Ignition switch ON
Engine running
Camshaft phaser
VVT control valve
Wire harness or connector
ECM
P000B-00
"B" Camshaft Position
Slow Response
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст