Chery Tiggo 5 (T21). Manual — part 516
48–
22
48
Apron Plate Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the front left wheel flare assembly (
2. Remove the left apron plate cover assembly.
a. Remove the fixing crew (1) from the left apron plate
cover assembly.
(Tightening torque: 3 ± 1 N·m)
b. Remove the plastic clip (arrow) from the left apron
plate cover assembly.
c. Using an interior crow plate, pry off the clip from the
left apron plate cover assembly.
d. Remove the left apron plate cover assembly in the
direction of arrow as shown in the illustration.
3. Remove the left apron plate assembly.
a. Remove 2 fixing crews (arrow) from the left apron
plate assembly.
(Tightening torque: 3 ± 1 N·m)
CAUTION
Be sure to wear safety equipment to prevent accidents when removing apron plate assembly.
Appropriate force should be applied when removing apron plate assembly. Be careful not to operate
roughly.
Try to prevent body paint surface from being scratched when removing apron plate assembly.
RT21480310
1
RT21480320
RT21480330
48–
23
48
b. Remove 7 plastic clips (arrow) from the left apron
plate assembly, and remove the left apron plate
assembly.
Installation
Installation is in the reverse order of removal.
RT21480331
CAUTION
Be sure to wear safety equipment to prevent accidents when installing apron plate assembly.
Try to prevent body paint surface from being scratched when installing apron plate assembly.
Make sure damaged clips are replaced and apron plate assembly is installed in place when installing
apron plate assembly.
48–
24
48
Front Wheel House Protector Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the front left wheel house protector assembly.
a. Remove 5 fixing crews (arrow) from the front left
wheel house protector assembly.
(Tightening torque: 3 ± 1 N·m)
b. Remove 2 fixing screws from the front left wheel
house protector assembly.
(Tightening torque: 3 ± 1 N·m)
c. Remove 6 plastic clips from the front left wheel house
protector assembly.
d. Remove the front left wheel house protector
assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing front wheel house protector
assembly.
Try to prevent body paint surface from being scratched when removing front wheel house protector
assembly.
RT21480210
RT21480220
CAUTION
Be sure to wear safety equipment to prevent accidents when installing front wheel house protector
assembly.
Try to prevent body paint surface from being scratched when installing front wheel house protector
assembly.
Make sure damaged clips are replaced and front wheel house protector assembly is installed in place
when installing front wheel house protector assembly.
48–
25
48
Fender Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the front left wheel flare assembly (
4. Remove the left apron plate cover assembly (
).
5. Remove the front bumper assembly (
).
6. Remove the front bumper left mounting bracket assembly (
).
7. Remove the front windshield lower garnish left cover plate.
a. Using a screwdriver wrapped with protective tape, pry
up the claws on front windshield lower garnish left
cover plate.
b. Remove the front windshield lower garnish left cover
plate.
8. Remove the left outer triangular block assembly.
a. Using an interior crow plate, pry off the clips from the
left outer triangular block assembly, and remove the
left outer triangular block assembly.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing fender assembly.
Try to prevent body paint surface from being scratched when removing fender assembly.
RT21480490
RT21480230
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст