Chery Tiggo 5 (T21). Manual — part 260
23–
35
23
e. Remove the coupling bolt and nut (arrow) between
lower part of rear suspension upper left swing arm
assembly and rear left trailing arm assembly.
(Tightening torque: 120 ± 10 N·m)
f. Lower the transmission carrier slowly to the
appropriate height and take off the rear coil spring
(arrow) and rear spring upper cushion (1) carefully.
g. Detach the rear buffer block (arrow) from the body.
h. Remove the fixing bolt (arrow) and detach the rear
rubber cushion assembly (1) from body.
(Tightening torque: 25 ± 5 N·m)
RT21230400
1
RT21230410
RT21230420
RT21230430
1
23–
36
23
Inspection
1. Check rear coil spring assembly.
a. Check rear coil spring for wear, cracks and permanent deformation due to excessive use. Replace as
necessary.
b. Check rear coil spring upper cushion, rear cushion and rear rubber cushion assembly for dirt, wear,
cracks, deformation or damage. Replace as necessary.
Installation
Installation is in the reverse order of removal.
CAUTION
Always tighten coupling bolts and nuts to the specified torque.
After installation is completed, lower vehicle and bounce it up and down several times to stabilize the
suspension.
23–
37
23
Rear Suspension Upper Swing Arm Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the rear left wheel (
).
2. Remove the rear suspension upper left swing arm assembly.
a. Remove the coupling bolt and nut (arrow) between
lower part of rear suspension upper left swing arm
assembly and rear left trailing arm assembly.
(Tightening torque: 120 ± 10 N·m)
b. Remove the coupling bolt and nut (arrow) between
upper part of rear suspension upper left swing arm
assembly and rear sub frame assembly.
(Tightening torque: 120 ± 10 N·m)
c. Remove the rear suspension upper left swing arm assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents.
Make sure that safety lock of lifter has been locked when removing and installing chassis parts.
It is not permitted to weld or modify suspension bearing parts.
When removing and installing chassis parts, replace self-locking nuts and rusted nuts for safety.
RT21230400
RT21220330
CAUTION
Always tighten coupling bolts and nuts to the specified torque.
23–
38
23
Rear Suspension Lower Swing Arm Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the rear left wheel (
).
2. Remove the rear suspension lower left swing arm assembly.
a. Remove the coupling nut (arrow) between lower part
of rear left stabilizer link assembly and rear
suspension lower left swing arm assembly.
(Tightening torque: 45 ± 5 N·m)
b. Remove 2 coupling bolts (arrow) between rear left
shock absorber assembly fixing bracket and rear left
trailing arm assembly.
(Tightening torque: 80 ± 8 N·m)
c. Remove the coupling bolt and nut (arrow) between
lower part of rear suspension lower left swing arm
assembly and rear left trailing arm assembly.
(Tightening torque: 120 ± 10 N·m)
CAUTION
Be sure to wear necessary safety equipment to prevent accidents.
Make sure that safety lock of lifter has been locked when removing and installing chassis parts.
It is not permitted to weld or modify suspension bearing parts.
When removing and installing chassis parts, replace self-locking nuts and the rusted nuts for safety.
RT21230370
RT21230380
RT21230390
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст