Chery Tiggo 5 (T21). Manual — part 296
26–
39
26
b. Remove the front left brake hose assembly (arrow)
from front left shock absorber assembly.
c. Remove the coupling bolt and washer (arrow)
between front left brake caliper assembly and front left
brake hose assembly.
(Tightening torque: 27 ± 2 N·m)
d. Remove the front left brake hose assembly.
Installation
Installation is in the reverse order of removal.
RT21260510
RT21260330
CAUTION
DO NOT allow brake fluid to be sprayed on your clothes or skin when removing brake hose, as the brake
fluid is corrosive.
CAUTION
Make sure to tighten coupling bolts and plug to the specified torque during installation.
Be sure to check brake system for leakage after installation. Repair or replace malfunctioning parts as
necessary.
Be sure to perform bleeding procedures for brake system after installation.
Be sure to add brake fluid to the proper level after installation.
26–
40
26
Rear Disc Brake Assembly
1 - Support Gasket
2 - Outer Brake Lining
3 - Inner Brake Lining
4 - Rear Disc Brake Caliper Fixing Bracket
5 - Rear Disc Brake Piston Dust Boot
6 - Rear Disc Brake Piston
7 - Rear Disc Brake Piston Seal Ring
8 - Rear Brake Cylinder
9 - Brake Caliper Locating Bolt Guide Pin (w/ Dust
Boot)
10 - Brake Caliper Locating Bolt
11 - Bleeder Plug
12 - Bleeder Plug Cap
RT21260520
3
2
1
4
5
6
7
8
9
10
11
12
26–
41
26
On-vehicle Inspection
1. Check brake disc runout.
a. Remove the rear wheel (
b. Secure the dial indicator (1) to the proper position.
Position the dial indicator pointer approximately 10
mm from the outer edge of rear brake disc.
c. Slowly rotate the brake disc (2) and check the runout.
Mark the lowest and highest points and record these
measurements.
d. Check the runout on the opposite side of brake disc in the same way. Mark the lowest and highest
points and record these measurements.
e. Compare the recorded runout value and limit value.
Maximum runout for front brake disc: 0.06 mm
f. If the runout exceeds the maximum value, replace the brake disc.
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Drain the brake fluid (
).
2. Remove the rear left wheel (
).
3. Remove the rear left brake caliper assembly.
a. Remove the coupling bolt and washer (arrow)
between rear left brake caliper assembly and rear left
brake hose assembly.
(Tightening torque: 20 ± 2 N·m)
RT21260530
2
1
CAUTION
Wash off brake fluid immediately if it comes in contact with any paint surface.
ENVIRONMENTAL PROTECTION
Drained brake fluid should be well kept in a container. Never discard it at will.
RT21260540
26–
42
26
b. Remove the coupling bolts (arrow) between rear left
brake caliper assembly and rear left brake bottom
board assembly.
(Tightening torque: 100 ± 10 N·m)
c. Remove the rear left brake caliper assembly.
4. Remove the rear left brake disc.
a. Remove the positioning screw (arrow) from rear left
brake disc, and remove the rear left brake disc.
(Tightening torque: 10 ± 1 N·m)
Disassembly
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
CAUTION
DO NOT allow brake fluid to be sprayed on your clothes or skin when removing brake hose, as the brake
fluid is corrosive.
RT21260550
RT21260560
WARNING
Never use high pressure when removing piston from the bore of brake caliper. Otherwise this may cause
personal injuries.
If it is needed to remove piston with compressed air. DO NOT allow the piston to face yourself or place
your hands around the brake caliper and piston.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст