Chery Tiggo 5 (T21). Manual — part 275
25–
33
25
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Check front left wheel speed sensor mounting bolt for looseness.
d. Check if excessive clearance exists between the installation position of front left wheel speed sensor and
front steering knuckle.
e. Check the installation position of front left wheel speed sensor for dirt.
a. Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
b. Drive the vehicle straight ahead, and read the data stream of front left wheel speed sensor with X-431 3G
diagnostic tester.
c. Check if the data change of front left wheel speed sensor matches the change of other wheel speed
sensors.
a. Remove the front left hub assembly.
b. Check for foreign matter, missing teeth or damage on the front left hub ring gear.
c. Check if the front left hub assembly is securely installed.
2
Check installation of front left wheel speed sensor
OK
Tighten mounting bolt properly, clean or
replace front left wheel speed sensor
NG
3
Check front left wheel speed sensor
OK
Replace front left wheel speed sensor
NG
4
Check front left hub ring gear
OK
Replace front left hub ring gear
NG
OK
25–
34
25
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the ABS control module assembly connector
E-085.
d. Disconnect the front left wheel speed sensor connector
E-060.
e. Using a digital multimeter, check for continuity between
the terminals of connector E-085 and connector E-060 to
check if there is an open in the wire harness and
connector according to the table below..
Standard Condition
f. Using a digital multimeter, check for continuity between
connector E-085 and body ground to check if the front left
wheel speed sensor is short to ground according to the
table below.
Standard Condition
5
Check wire harness and connector (front left wheel speed sensor - ABS control module
assembly)
RT21250230
E-085
13
12 11 10 9 8 7 6 5 4 3 2
24 23 22 21 20 19 18 17 16 15 14
37 36 35 34 33 32 31 30 29 28 27 26
1
38
25
-
+
E-060
1
2
Multimeter
Connection
Condition
Specified
Condition
E-085 (8) -
E-060 (2)
Always
Continuity
E-085 (19) -
E-060 (1)
Always
Continuity
E-085 (8) -
E-060 (1)
Always
No continuity
E-085 (19) -
E-060 (2)
Always
No continuity
E-060 (1) -
E-060 (2)
Always
No continuity
E-085 (8) -
E-085 (19)
Always
No continuity
RT21250240
E-085
13
12 11 10 9 8 7 6 5 4 3 2
24 23 22 21 20 19 18 17 16 15 14
37 36 35 34 33 32 31 30 29 28 27 26
1
38
25
-
+
Multimeter
Connection
Condition
Specified
Condition
E-085 (8) - Body
ground
Always
No continuity
E-085 (19) - Body
ground
Always
No continuity
25–
35
25
g. Connect the negative battery cable.
h. Turn ignition switch ON.
i. Using a digital multimeter, measure the voltage between
connector E-085 and body ground to check if the front left
wheel speed sensor is short to power supply according to
the table below.
Standard Condition
a. Use X-431 3G diagnostic tester to clear the DTC.
b. Start the engine.
c. Drive the vehicle at 15 km/h or more, read the ABS control module assembly DTC again with X-431 3G
diagnostic tester.
d. Check if the same DTC is output.
RT21250250
E-085
13
12 11 10 9 8 7 6 5 4 3 2
24 23 22 21 20 19 18 17 16 15 14
37 36 35 34 33 32 31 30 29 28 27 26
1
38
25
-
+
V
Multimeter
Connection
Condition
Specified
Condition
E-085 (8) - Body
ground
Ignition switch ON Approximately 0 V
E-085 (19) - Body
ground
Ignition switch ON Approximately 0 V
Repair or replace wire harness and
connector between front left wheel speed
sensor and ABS control module assembly
NG
6
Reconfirm DTCs
OK
System operates normally
NO
Replace ABS control module assembly
YES
25–
36
25
Code
C0034-00 Right Front Wheel Speed Sensor
Code
C0034-09 Right Front Wheel Speed Sensor
Code
C0034-11 Right Front Wheel Speed Sensor
Code
C0034-12 Right Front Wheel Speed Sensor
Code
C0034-13 Right Front Wheel Speed Sensor
Code
C0034-29 Right Front Wheel Speed Sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст