Chery Tiggo. Manual — part 262
3.
CHECK FLUID PRESSURE SENSOR POWER SUPPLY
• Stop vehicle and turn ignition switch off.
• Turn the ignition switch on.
• Check sensor power supply between sensor termi-
nal C1 and ground in the sensor electrical connec-
tor E-037.
• 5 V should exist.
Is the check result normal?
Yes
>>
Go to the next step.
No
>>
Repair or replace the open circuit or short
to ground or short to power in harness or
connectors.
If circuit is normal, replace TCM.
4.
CHECK FLUID PRESSURE SENSOR GROUND CIRCUIT
• Turn the ignition switch off.
• Disconnect TCM connector.
• Check for harness continuity between the following terminals:
A/T ASSEMBLY
TERMINAL
TCM
CONNECTOR
TERMINAL
CONTINUITY
C3
25
Yes
• Check the harness for short to power and short to ground.
Is the check result normal?
Yes
>>
Go to the next step.
No
>>
Repair or replace the open circuit or short to power or short to ground in harness connectors.
5.
CHECK FLUID PRESSURE SENSOR SIGNAL
• Connect fluid pressure sensor connector.
• Connect TCM connector.
• Turn the ignition switch on.
• Check sensor signal voltage between sensor terminal 55 and 25 in the sensor electrical connector E-037.
• 1.4 V should exist.
Is the check result normal?
Yes
>>
Go to step 8.
No
>>
Go to the next step.
DIAGNOSIS & TESTING
LTSMD080054
6.
CHECK FLUID PRESSURE SENSOR SIGNAL CIRCUIT
• Turn the ignition switch off.
• Disconnect TCM and sensor connector.
• Check harness continuity between fluid pressure sensor terminal C2 and TCM terminal 55.
• Check short to ground and short to power supply.
Is the check result normal?
Yes
>>
Go to the next step.
No
>>
Check harness for an open or short to ground or short to power supply in harness or connectors.
7.
CHECK THE FLUID PRESSURE SENSOR
• Check fluid pressure sensor resistance between sensor terminal C2 and C3 in A/T assembly connector E-037.
• Approximately 20 K⍀ should exist.
Is the check result normal?
Yes
>>
Go to the next step.
No
>>
Replace the fluid pressure sensor.
8.
CHECK DTC
• With the X-431 scan tool, read TCM DTCs.
• Refer to ⬙DTC Confirmation Procedure⬙.
Is DTC P0840 present?
Yes
>>
The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
No
>>
Replace the TCM.
DIAGNOSIS & TESTING
08
P1928 - Shift Lock Solenoid Valve Circuit Shorted To Voltage
DIAGNOSIS & TESTING
LTSMW080013T
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO.
DTC
DEFINITION
DTC
DETECTION
CONDITION
DTC SET CONDITION
POSSIBLE
CAUSES
P1928
Shift lock
solenoid circuit
short to power
supply
Ignition on or
vehicle is driving
The Transaxle Control Module (TCM)
will set this DTC when the TCM
detects that the shift lever lock
solenoid circuit shorted to power
supply.
• Shift lock
solenoid valve
• Harness or
connectors (The
sensor circuit is
shorted)
• Transaxle
Control Module
(TCM)
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on, with the scan tool, view and erase stored DTCs in the TCM.
• Start the engine and warm it to normal operating temperature.
• Try to operate the shifter selector.
• With the scan tool, select view DTC and data stream.
• If the DTC is detected, the DTC condition is current. Go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnostic Help and Intermittent DTC Trou-
bleshooting in Section 08 Transaxle & Transfer Case for more information).
• If using the appropriate diagnostic test tool, you can diagnose the TCM harness while the TCM is still con-
nected.
• Using the appropriate diagnostic test tool in this way will help prevent electrical connector terminal damage.
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
Diagnostic Procedure
1.
CHECK SHIFT LOCK SOLENOID VALVE SIGNAL
• With the scan tool, select view DTC and data stream.
• Start the engine.
• Monitor the value of the gear position as indicated in the following table while driving:
SELECT
POSITION
RANGE
SHIFT
SOLENOID
VALVE 1
SHIFT
SOLENOID
VALVE 2
SHIFT
SOLENOID
VALVE 3
SHIFT
SOLENOID
VALVE 4
P
0
-
-
#
-
R
R
-
-
-
-
N
0
-
-
#
-
D
1
-
-
#
#
2
-
#
-
#
3
-
-
-
-
4
#
#
-
-
DIAGNOSIS & TESTING
08
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст