Chery Tiggo. Manual — part 60
Lower Balance Shaft
Removal & Installation
1 - Upper Balance Shaft Rear Bearing
2 - Upper Balance Shaft Front Bearing
3 - Upper Balance Shaft
4 - Oil Pressure Switch
5 - Front Cover Gasket
6 - Oil Pump Driven Gear
7 - Oil Pump Drive Gear
8 - Front Cover
9 - Upper Balance Shaft Oil Seal
10 - Crankshaft Front Oil Seal
11 - Oil Filter Adapter Gasket
12 - Oil Filter Adapter
13 - Pressure-Relief Valve
14 - Pressure Relief Spring
15 - Pressure-Relief Valve Seal
16 - Oil Filter
17 - Pressure Relief Valve Plug
18 - Plug
19 - Front Cover Bolt
20 - O-Ring
21 - Oil Pump Oil Seal
22 - Oil Pump Cover
23 - Lower Balance Shaft
24 - Lower Balance Shaft Rear Bearing
ON-VEHICLE SERVICE
LTSM020133
NOTE :
The following special tools are required to perform the repair procedure:
• MD-991603 - Balance Shaft Bearing Puller Limiter
• MD-998162 - Plug Spanner
• MD-998371 - Balance Shaft Bearing Puller
• MD-998372 - Balance Shaft Bearing Puller
• MD-998375 - Crankshaft Front Oil Seal Installer
• MD-998705 - Balance Shaft Bearing Installer
• MD-998727 - Oil Pan Remover
• MD-998783 - Plug Spanner Fixer
• MD-991828 - Oil Filter Wrench
• MD-991396 - Oil Filter Wrench
1. Raise and support the vehicle.
2. Loosen the oil drain plug and drain the oil.
3. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
4. Remove the upper balance shaft timing belt (See Upper Balance Shaft Timing Belt Removal & Installation in
Section 02 Engine).
5. Remove the oil pan retaining bolts.
(Tighten: Oil pan bolts to 18 N·m)
6. Using special tool MD-998727 (1), remove the oil
pan.
NOTE: Insert the special tool between cylinder
block and the oil pan. Do not use a screwdriver or
chisel, otherwise the edge of oil pan may be dis-
torted and oil leaks will occur.
7. Remove the oil strainer retaining bolts.
(Tighten: Oil strainer bolts to 19 N·m)
8. Remove the oil strainer.
9. Remove the oil strainer gasket.
10. Secure the lower balance shaft. Remove the plug
from the cylinder block and then insert a holder (1)
(8 mm diameter) into the hole.
NOTE: If the holder can be inserted more than 60
mm, then the timing marks are aligned. If the
holder could not be inserted more than 20-25 mm,
the lower balance shaft pulley should be rotated
one revolution and the timing marks should be then
be aligned. Keep the holder installed until the
installation of the timing belt is complete.
ON-VEHICLE SERVICE
LTSM020134
LTSM020186
02
11. Remove the lower balance shaft bolt (1).
(Tighten: Lower balance shaft bolt to 55 N·m)
12. Remove the lower balance shaft pulley.
13. Remove the crankshaft pulley bolt.
(Tighten: Crankshaft pulley bolt to 120 N·m)
14. Using special tool MD-9988778 (1), remove the
crankshaft pulley.
15. Using special tool MD-9988785 (1), lock the upper
balance shaft pulley in place.
16. Remove the upper balance shaft pulley bolt.
(Tighten:
Upper
balance
shaft
pulley
bolt
to
45 N·m)
17. Using special tool MD-9988778 (1), remove the
upper balance shaft pulley.
18. Remove the front cover.
19. Remove the front cover gasket.
20. Remove the lower balance shaft.
21. Remove the lower balance shaft bearings (See
Lower Balance Shaft Bearing Replacement in Sec-
tion 02 Engine).
22. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020174
LTSM020052
LTSM020054
LTSM020172
Lower Balance Shaft Bearing Replacement
1. Using special tool MD-998371 (1), remove the
lower balance shaft front bearing from the cylinder
block.
2. Using special tool MD-998705 (1) MD-991603 (2),
remove the lower balance shaft rear bearing from
the cylinder block.
3. Using special tool MD-998705 (2), install the rear
bearing.
NOTE :
Align the oil holes (1) in the rear bearing and the cylin-
der block.
ON-VEHICLE SERVICE
LTSM020137
LTSM020138
LTSM020139
02
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст