Chery Tiggo. Manual — part 158
P0201 - Cylinder 1 - Injector Circuit
P0202 - Cylinder 2 - Injector Circuit
P0203 - Cylinder 3 - Injector Circuit
P0204 - Cylinder 4 - Injector Circuit
DIAGNOSIS & TESTING
LTSMW030029T
03
DIAGNOSIS & TESTING
LTSMW030030T
Check reference values between ECM terminals and ground under the following conditions:
ECM TERMINAL NO.
ITEM
CONDITION
DATA (AVERAGE DC
VOLTAGE)
6
Injector 2
• Engine is running
• Warm-up condition
• Idle
• Accelerate suddenly
Voltage: 11 - 14 V
7
Injector 3
27
Injector 1
47
Injector 4
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO.
DTC DEFINITION
DTC DETECTION
CONDITION
POSSIBLE CAUSE
P0201
Cylinder 1 - Injector Circuit
Engine is running
• Injector
• Harness or connectors
• ECM
P0202
Cylinder 2 - Injector Circuit
P0203
Cylinder 3 - Injector Circuit
P0204
Cylinder 4 - Injector Circuit
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it to normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
Diagnostic Procedure
1.
CHECK GROUND CONNECTIONS
• Turn ignition switch off.
• Loosen and retighten ground screws on the body (See Ground Inspection in Section 03 Electronic Engine Con-
trols).
• Inspect ground connections E-207 and E-208 mounting position (See Vehicle Wiring Harness Layout - Engine
Room Harness (With 2.0L Engine) in Section 16 Wiring).
Are the ground connections OK?
Yes
>>
Go to the next step.
No
>>
Repair or replace ground harness or connections.
DIAGNOSIS & TESTING
03
2.
INSPECTION START
• Start engine.
Is any cylinder ignited?
Yes
>>
If with the X-431, go to the next step.
If without the X-431, go to step 4.
No
>>
Go to step 5.
3.
PERFORM ACTIVE TEST FUNCTION
• Start engine.
• Select ⬙ACTIVE TEST⬙ menu.
• Perform injector active test.
• Make sure that each test produces a momentary engine speed drop.
Is the check result normal?
Yes
>>
Go to step 11.
No
>>
Go to step 5.
4.
CHECK FUNCTION OF INJECTORS
• Listen to injectors for operating sound one by one.
Does a clicking noise exist for all injectors?
Yes
>>
Go to step 11.
No
>>
Go to the next step.
5.
CHECK INJECTOR ELECTRICAL CONNECTOR
• Turn ignition switch off.
• Disconnect the injector electrical connector (1).
• Inspect the electrical connector for damage.
Is the electrical connector OK?
Yes
>>
Go to the next step.
No
>>
Repair or replace the electrical connector
as necessary.
DIAGNOSIS & TESTING
BESM040006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст