Chery Tiggo. Manual — part 229
DIAGNOSIS & TESTING
Generator Noise
Noise emitting from the generator may be caused by the following:
• Worn, loose or defective bearings
• Loose or defective drive pulley
• Incorrect, worn, damaged or misadjusted drive belt
• Loose mounting bolts
• Misaligned drive pulley
• Defective stator
• Damaged internal fins
ON-VEHICLE SERVICE
Generator
Removal & Installation - 1.6L & 1.8L & 2.0L
1. Disconnect the negative battery cable.
2. Disconnect the generator electrical connector.
3. Remove the engine drive belt (See Drive Belt Removal & Installation in Section 02 Engine).
4. Remove the generator cable nut (1) connecting the
positive cable to the generator.
(Tighten: Generator cable nut to 13 N·m)
5. Remove two generator mounting bolts (1).
(Tighten: Generator mounting bolts to 30 N·m)
6. Remove the generator from the engine.
7. Installation is in the reverse order of removal.
BESM050002
BESM050003
05
Removal & Installation - 2.4L
1. Disconnect the negative battery cable.
2. Remove the engine drive belt (See Drive Belt
Removal & Installation in Section 02 Engine).
3. Remove the generator cable nut (1) connecting the
positive cable to the generator.
(Tighten: Generator cable nut to 10 N·m)
4. Disconnect the electrical connector (2).
5. Remove the two generator adjustment bracket
bolts (1).
(Tighten: Generator adjustment bracket bolts to
25 N·m)
6. Remove the generator from the engine.
7. Installation is in the reverse order of removal.
Generator Inspection
1. Start the engine.
NOTE: If the battery warning lamp illuminates, there may be a problem with the charging system.
2. With the engine running, check the output voltage of the generator with a digital multimeter (note the voltage).
3. If the voltage is between 14.1 V - 14.7 V, the generator is good.
ON-VEHICLE SERVICE
LTSM050003
LTSM050004
COOLING
06
CONTENTS
page
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06-1
COOLING SYSTEM
GENERAL INFORMATION
06-2
Description
06-2
Operation
06-4
Specifications
06-5
Special Tools
06-5
Electrical Schematics
06-6
DIAGNOSIS AND TESTING
06-11
Cooling System Pressure Test
06-11
Cooling System Concentration Test
06-11
Cooling System Troubleshooting Chart
06-12
ON-VEHICLE SERVICE
06-13
Cooling System Draining and Filling
06-13
Cooling System Draining Procedure
06-13
Cooling System Filling Procedure
06-13
Thermostat
06-14
Description
06-14
Operation
06-14
Removal & Installation - 1.6L & 1.8L &
2.0L
06-14
Removal & Installation - 2.4L
06-15
Thermostat Inspection
06-16
Coolant Pump
06-16
Removal & Installation - 1.6L & 1.8L &
2.0L
06-16
Removal & Installation - 2.4L
06-17
Coolant Pump Inspection
06-17
Radiator
06-17
Description
06-17
Operation
06-17
Removal & Installation
06-17
Cooling Fan
06-18
Description
06-18
Operation
06-19
Removal & Installation
06-19
Cooling Fan Inspection
06-19
06
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст