Chery Tiggo. Manual — part 457
Front Wiper Link
Removal & Installation
1. Disconnect the negative battery cable.
2. Remove the left lower trim panel of the front wind-
shield.
3. Remove the mounting bolts (1) and the front wiper
motor electrical connector (2), then remove the
wiper link.
(Tighten: Wiper arm linkage mechanism mounting
bolts to 10 ± 1 N·m)
4. Installation is in the reverse order of removal.
Washer Bottle
Removal & Installation
1. Disconnect the negative battery cable.
2. Remove the front bumper (See Front Bumper
Removal & Installation in Section 15 Body &
Accessories).
3. Disconnect the washer hose and the washer pump
electrical connector.
4. Remove the mounting bolts (1) as shown to
remove the washer bottle.
5. Installation is in the reverse order of removal.
Washer Pump
Removal & Installation
1. Disconnect the negative battery cable.
2. Remove the front bumper (See Front Bumper Removal & Installation in Section 15 Body & Accessories).
3. Disconnect the washer hose and the washer pump electrical connector.
4. Drain the washer fluid.
5. Remove the washer pump assembly.
6. Installation is in the reverse order of removal.
WIPERS AND WASHERS
LTSM150034
LTSM150101
15
Wiper Switch
Removal & Installation
1. Disconnect the negative battery cable.
2. Remove the steering wheel (See Steering Wheel Removal & Installation in Section 11 Steering).
3. Remove the steering column shroud retaining
screws (1) and then remove the shroud.
4. Disconnect the wiper switch electrical connector.
5. Loosen the clamp and remove the wiper switch.
6. Installation is in the reverse order of removal.
WIPERS AND WASHERS
LTSM110031
LTSM150106
WIRING
16
CONTENTS
page
Wiring Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1
Vehicle Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-12
Vehicle Ground Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-27
Vehicle Fuse Box Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-37
Vehicle Wiring Harness Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-44
WIRING INFORMATION
GENERAL INFORMATION
16-2
Description
16-2
Electrical Schematics
16-2
International Symbols
16-3
ELECTRICAL TROUBLESHOOTING
16-5
Troubleshooting Wiring Problems
16-5
Testing For Voltage
16-5
Testing For Continuity
16-5
Testing For A Short To Ground
16-5
Intermittent and Poor Connections
16-5
ELECTRICAL TROUBLESHOOTING
TOOLS
16-6
Jumper Wires
16-6
Voltmeter
16-6
Ohmmeter
16-7
ELECTRICAL REPAIR
16-8
Wire Repair
16-8
Fuse Replacement
16-8
ELECTRICAL COMPONENTS
16-9
Battery Cable
16-9
Sensors, Switches, and Relays
16-9
Connectors
16-10
16
GENERAL INFORMATION
Description
The wiring information includes wiring diagrams, proper wire and connector repair procedures, details of wire harness
routing and retention, connector pin-out information and location views for the various wiring harness components,
splices and grounds.
Electrical Schematics
The electrical schematics are grouped into individual service manual chapters. If a component is most likely found in
a particular group, it will be shown complete (all wires, connectors, and pins) within that group. For example, the
Engine Control Module (ECM) is most likely to be found in Chapter 03 (Electronic Engine Controls), so it is shown
there complete. It can, however, be shown partially in another group if it contains some associated wiring.
Chery electrical schematics are designed to provide information regarding the vehicles wiring content. In order to
effectively use the wiring diagrams to diagnose and repair Chery vehicles, it is important to understand the following
features and characteristics:
• Diagrams are arranged such that the power (B+) side of the circuit is placed near the top of the page, and the
ground (B-) side of the circuit is placed near the bottom of the page.
• All switches, components, and modules are shown in the at rest position with the doors closed and the key
removed from the ignition switch.
• Components are shown with a solid line around the component.
• It is important to realize that no attempt is made on the diagrams to represent components and wiring as they
appear on the vehicle. For example, a short piece of wire is treated the same as a long one.
• Switches and other components are shown as simply as possible, with regard to function only.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст