Chery S11 / Chery QQ. Manual — part 190
Chery QQ Maintenance Manual Chassis System
Abnormal
Replace HECU
Normal
Abnormal Replace fuse or harness
Normal
Replace ECU
No
2、Wheel speed sensor:00283,00285,00290,00287
Remove motor harness
plug and connect battery
to motor plug to see if
motor works
Check fuse and ABS ECU
connector
Connect motor harness
Turn on ignition
switch
Clear DTC
Diagnose HECU with instrument
Possible cause
2、DTC 00283,00285,00290,00287
Means no signal put out at 20km/h
Hint: No sensor, sensor coil and harness
short, too big or too small for clearance
between sensor and tooth ring or bad tooth
ring
No sensor
Sensor coil and harness short
Too big or too small for
clearance between sensor and
tooth ring
Bad tooth ring
ABS ECU fault
Faulty appears again?
Yes
Refer to intermittence malfunction
42
Chery QQ Maintenance Manual Chassis System
Reinstallation
Yes
Abnormal
Normal
3、Wheel speed sensor
Possible cause
3、DTC 00283,00285,00290,00287
Means signal is over specification at 20km/h
Hint: Short sensor coil, tooth ring damage
or too big clearance.
Bad touch or short between coil
and harness
Too big or small for clearance
between sensor and tooth ring
Bad tooth
ABS ECU fault
Reinstallation
Yes
Abnormal
Normal
Normal
Replace ABS ECU
Normal
Normal
Normal
Sensor install
normal?
Check each tooth ring
Check clearance
Check each sensor
Check harness between
sensor and ABS ECU
Install sensor
normal?
Check out put voltage
on ABS pin 25
Check each tooth
ring
Check each tooth ring
Check clearance
NO
Replac
Replac
Fix or replace
Abnormal
Fix or replace
Abnormal
Abnormal
Replac
Abnorm
Abnorm
Abnorm
Replac
Check out put voltage on
ABS pin 25
Replace ABS
Check harness between
sensor and ABS ECU
43
Chery QQ Maintenance Manual Chassis System
4、Wheel speed sensor
Possible fault
4、DTC 00283,00285,00290,00287
Means open or short sensor
Hint:Bad contact of sensor or short harness
or circuit fault on ABS ECU
Open sensor coil
Short sensor coil
Short between sensor and harness or
source
ABS ECU signal fault
Check each sensor
Normal
Abnormal
Abnormal
Yes
Check harness between
ECU and sensor
Normal
RemoveABS ECU co-
nnector and mea-
sure
resistance
between terminals
of ABS ECU
Specifications :
1.0~1.3kΩ
Shake harness or
connector
MK20I/E
Front left:1-2
Front right:19-20
Rear left:5-6
Rear right:22-23
Check connector of
sensor
Fault appears aga-
in?
Refer to ser-
vice hint
Fix connecter
Normal
Replace ABS ECU
5、ABS coding err
Possible cause
5、DTC 01044
Means the software and hardware problem
·Bad connect of ABS harness
·ABS ECU coding fault
44
Chery QQ Maintenance Manual Chassis System
Recoding
Yes
Abnormal
Replace harness
6、Supply terminal 30
Possible cause
6、DTC 00668
Means too high source voltage
·ABS fuse burn out
·Too low or too high battery
voltage
·ABS harness damage
·ABS ECU damage
Normal
Check ABS fuse 30 Replace fuse
Normal
Abnormal Abnormal
Check ABS harness Fix connecter
Normal
Try again. No Normal?
Yes
Normal
Check battery
Normal
Replace ABS ECU
Check if coding correct
Check if ABS harness god
NO
Disconnect between ABS
harness and ECU, turn on
switch
and
measure
voltage:
Terminal8,9: 9.5-16.5V
Terminal 24,25: 9.5-16.5V
MK20I/E:
Terminal8,4: 9.5-16.5V
7、ABS service preternatural
Possible cause
7、DTC 01130
Means interfere of high frequency or bad
signal
·Interfere of high frequency
·Bad sensor or harness
·ABS ECU damage
45
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст