Chery S11 / Chery QQ. Manual — part 232
Chery QQ Maintenance Manual 465 EFI System
DTC 14 TPS
The diagram of TPS
No. Operation
steps Test
results
Next step
1
Turn on ignition key.
Next
Yes Next
2
Pull out connector of A/C evaporator temperature
sensor, measure if the volt between 2 pins is 5V
with multimeter.
No
5
Yes Next
3
Measure the resistance between pin (1) and (2) if
in 1.6 to 2.4k with multimeter.
No Replace
sensor
Yes Replace
sensor
4
Run slowly TPS from one end to another and
check any open or short between pin (1) and (3).
No Replace
ECU
Yes Repair
or
replace harness
5
Connect adaptor between ECU and harness,
check any open or short between pin 12 , 30 of
ECU and pin (1) and (2) of sensor with
multimeter.
No Replace
ECU
Note: For M1.5.4 with distributor, 5V voltage is supplied by pin 12 of ECU to TPS and Hall
sensor. If the DTC dislays when vehicle cannot be started, it cannot be clear DTC from TPS.
Please check if short in Hall sensor.
25
Chery QQ Maintenance Manual 465 EFI System
DTC 15 KS
Diagram for KS
No. Operation
steps
Test
results
Next step
1
Turn off ignition key, engine nor run.
Next
Yes Next
2
Pull out connector of KS sensor, measure if the
resistance between pin 1, pin 2 of sensor and
between pin1 and pin 3 is over 1M with multimeter.
No
Replace sensor
Yes Next
3
Slightly knock around sensor with small hammer
and check if any AC signals putout between pin1
and pin2 of sensor.
No Replace
sensor
4
Turn on ignition key but engine not run
Next
Yes
Repair or replace
harness
Connect adaptor between ECU anfd harnesses and
check any open or short between pin 11, pin 30,
pin19 of ECU and pin 1 and pin2 and pin 3 with
multimeter.
No Replace
ECU
26
Chery QQ Maintenance Manual 465 EFI System
DTC 16 MAP and IAT
Diagram of MAP and IAT
No. Operation
steps
Test
results
Next step
1
Turn on ignition key.
Next
Yes 4
2
Pull out the connectors on harness of
MAP and IAT and check if the voltage
between pin1 and pin 2 is 5V with
multimeter.
No Next
Yes
Repair or replace
harness
3
Connect the adaptor between ECU and
harness, check if open or short between
pin 30, pin 12, pin 7 of ECU and pin 1,
pin 3, pin 4 separately with multimeter.
No Next
4
Turn on ignition key but engine not run
Next
Yes Replace
ECU
5
Put on N shaft and run engine at idle. Step
down accelarate pedal to fully open.
Check if the voltage between pin 4 and
pin 1 of sensor is incrasing with
multimeter.
No
Replace ECU or
sensor
27
Chery QQ Maintenance Manual 465 EFI System
DTC 17 Oxygen sensor
The diagram of oxygen sensor
No.
Operation Steps
Test result Next step
1
Turn on ignition key.
Next
Yes Next
2
Put out the connector on oxygen sensor and
check if the voltage between pin 1 and pin 2 is
12 V.
No 4
Yes Replace
ECU
3
Check if the resistance between pin 1 and pin 2
on oxygen sensor is from 6 to 25.
No Replace
sensor
Yes Replace
4
Check if the fuse of heated oxygen sensor burns
out.
No Next
Yes
Repair or replace
harness
5
Check if open or short between pin 1 on sensor
and pin 87 on fuel pump relay, check open or
short between pin 2 and pin 59.
No Next
6
Insert the connector of oxygen sensor harness.
Put N shaft and run engine at idle to normal
coolant temperature.
Next
Yes Next
7
Put out connector on oxygen sensor harness;
check if ther is any 0.1 –0.9 V output voltage
between pin 4 and pin 3.
Yes Replace
sensor
Yes
Repair or replace
harness
8
Connect adaptor between ECU and harness.
Check if open or short between pin 10 on ECU,
pin 28 and pin 3, pin 4 separately.
No Replace
ECU
DTC 18 IAT
28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст