Chery Fora (Elara A520). Manual — part 120

CHERY A520 SERVICE MANUAL CHASSIS

67

III. DISASSEMBLY AND ASSEMBLY
OF REAR LOWER CONTROL ARM

Disassembly sequence:

1.

Dismount the bolts connecting the
control arm and vehicle body.

Mounting torque: 100~120Nm

2.

Dismount the bolts connecting the
control arm and rear vibration damper.

Mounting torque: 80

±

5Nm

3.

Dismount the bolts connecting the
control arm and rear trailing arm.

Mounting torque: 90～100Nm

4.

Dismount the

lower

control

arm

assembly.

Assembly sequence:

1.

Assemble the rear lower control arm
according to the disassembly sequence.

2.

Precautions:

After assembly, all bolts must be fastened up
to specified torques.

CHERY A520 SERVICE MANUAL CHASSIS

68

IV. DISASSEMBLY AND ASSEMBLY
GUIDE BAR

Disassembly sequence:

1.

Dismount the four fastening bolts of
wheel.

Mounting torque:110±10Nm

2.

Take down the tire.

3.

Dismount the bolts connecting guide bar
and rear trailing arm assembly.

Mounting torque: 90～100Nm.

4.

Dismount the bolts connecting guide bar
and vehicle body.

Mounting torque: 100～120Nm

Assembly sequence:

1.

Assemble the guide bar according to the
disassembly sequence.

2.

Precautions:

After mounting, all bolts must be fastened up
to specified torques.

CHERY A520 SERVICE MANUAL CHASSIS

69

V. ASSEMBLY OF REAR AXLE AND SUSPENSION SYSTEM

ASSEMBLY SEQUENCE:

——

Use bolt 23 to connect the upper control arm 3 and trailing arm 2(one weld nut installed
on the rear trailing arm); The left and right sides are the same, and the fastening torque
is 90～100

m

N

⋅

. Do not fasten the bolt at this time.

——

Use bolt 21 and nut 22 to connect the guide bar 20 and trailing arm 2. The left and right
sides are the same, and the fastening torque is 90～100

m

N

⋅

.Don not fasten the bolt

and nut at this time.

——

Use bolt 19 and nut 18 to connect the rear lower control arm 17 and trailing arm2. The
left and right sides are the same, and the fastening torque is90～100

m

N

⋅

. Do not

fasten the bolt and nut at this time.

——

Use nut 8(2 pieces) to connect the rear strut 9 and vehicle body. The left and right sides
are the same and the fastening torque is 50

±

10

m

N

⋅

.

——

Use bolt 1 to connect the trailing arm and vehicle body ( the vehicle body has one weld
nut and include the well-connected upper and lower control arms and guide bar). The

1 Bolt

2 Trailing Arm

3 Upper Control Arm

5 Gasket

23 Bolt

8 Nut

9 Rear Sliding Pole

10 Bolt

11 Nut

12 Nut

14 Adjusting Bolt

17 Lower Control Arm

18 Nut

19 Bolt

20 Guide Bar

21 Bolt

22 Nut

13 Gasket

6 Gasket

7 Nut

15 Bolt

16 Adjusting Bolt

4 Nut

CHERY A520 SERVICE MANUAL CHASSIS

70

left and right sides are the same, and the fastening torque is 100～120

m

N

⋅

. Do not

fasten the bolt at this time.

——

Use bolt 10 and nut 11 to fix the rear strut 9 and rear lower control arm17( fix them at
the position as the arrow illustrated). The left and right sides are the same, and the
fastening torque is 80

±

5

m

N

⋅

. Do not fasten the bolt and nut at this time.

——

Use adjusting bolt 16, gasket5 and nut 4 to connect the rear upper control arm and
vehicle body. The left and right sides are the same, and the fastening torque is 100～
120

m

N

⋅

. Do not fasten the bolt and nut at this time.

——

Use bolt 15, gasket 6 and nut 7 to connect the guide bar and vehicle body. The left and
right sides are the same, and the fastening torque is 100～120

m

N

⋅

. Do not fasten the

bolt and nut at this time.

——

Use adjusting bolt 14, gasket 13 and nut 12 to connect the rear lower control arm and
vehicle body. The left and right sides are the same, and the fastening torque is 100～
120

m

N

⋅

. Do not fasten the bolt and nut at this time.

——

Fasten the above-mentioned bolts and nuts to specified torques in turn.