Chery Fora (Elara A520). Manual — part 151
CHERY·A21 SERVICE MANUAL ENGINE EFI SYSTEM
43
DTC: P0340 Phase sensor signal failure
No.
Operating steps
Result Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the phase sensor joint from the cable; check the
voltage value by multimeter between phase sensor joint pin
No.3 and No.1; and observe if it is around 12V.
No
Next step
Yes
Repair or
replace the
cable
3
Check if there is open circuit or short circuit to ground
between circuit of phase sensor joint pin No.3 and main
relay pin No.87; check if there is bad contact of phase
sensor connector No.1.
No
Next step
Yes
To step 6
4
Check the voltage if it is around 9.9V between phase sensor
joint pin No.2 and power supply cathode.
No
Next step
Yes
Repair or
replace cable
5
Check if there is open circuit or short circuit to power
supply or to ground between phase sensor joint pin No.2
and ECU pin No.79.
No
Next step
Yes
Diagnosis help
6
Check the camshaft signal disc if it is in good conditions.
No
Replace signal
disc
DTC: P0342 Much lower voltage of the phase sensor
No.
Operating steps
Result Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the phase sensor joint from the cable; check the
voltage value by multimeter between phase sensor joint pin
No.3 and No.1; and observe if it is around 12V.
No
Next step
Yes
Repair or
replace the
cable
3
Check if there is open circuit or short circuit to ground
between circuit of phase sensor joint pin No.3 and main
relay pin No.87; check if there is bad contact of phase
sensor connector No.1.
No
Next step
Yes
To step 6
4
Check the voltage if it is around 9.9V between phase sensor
joint pin No.2 and power supply cathode.
No
Next step
Yes
Repair or
replace cable
5
Check if there is open circuit or short circuit to power
supply or to ground between the circuit of phase sensor
joint pin No.2 and ECU pin No.79.
No
Next step
Yes
Diagnosis help
6
Check the camshaft signal disc if it is in good conditions.
No
Replace signal
disc
CHERY·A21 SERVICE MANUAL ENGINE EFI SYSTEM
44
DTC: P0343 Much higher voltage of the phase sensor
No.
Operating steps
Result
Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the phase sensor joint from the cable; check
the voltage value by multimeter between phase sensor
joint pin No.3 and No.1; and observe if it is around
12V.
No
Next step
Yes
Repair or replace
the cable
3
Check if there is open circuit or short circuit to ground
between circuit of phase sensor joint pin No.3 and main
relay pin No.87; check if there is bad contact of phase
sensor connector No.1.
No
Next step
Yes
To step 6
4
Check the voltage if it is around 9.9V between phase
sensor joint pin No.2 and power supply cathode.
No
Next step
Yes
Repair or replace
cable
5
Check if there is open circuit or short circuit to power
supply or to ground between the circuit of phase sensor
joint pin No.2 and ECU pin No.79.
No
Next step
Yes
Diagnosis help
6
Check the camshaft signal disc if it is in good
conditions.
No
Replace signal
disc
DTC: P0443 Canister control valve drive grade control circuit failure
No.
Operating steps
Result
Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the canister control valve joint from the cable;
check the voltage value by multimeter between this
joint pin No.1 and power supply cathode; and observe
if it is around 12V.
No
Next step
Yes
Repair or replace
the cable
3
Check if there is open circuit or short circuit to ground
of the canister control valve power supply ends circuit.
No
To step No.2
Yes
Next step
4
Check the resistance value if it is around 22-30Ωwhen
it is 20℃ between canister control valve pin No.1 and
pin No.2.
No
Replace the valve
Yes
Diagnosis help
5
Check the voltage if it is around 3.7V between canister
control valve joint pin No.1 and power supply cathode.
No
Next step
Yes
Repair or replace
cable
6
Check if there is open circuit between the circuit of
canister joint pin No.2 and ECU pin No. 46.
No
Diagnosis help
CHERY·A21 SERVICE MANUAL ENGINE EFI SYSTEM
45
DTC: P0444 Much lower voltage of canister control valve drive grade control circuit
No.
Operating steps
Result
Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the canister control valve joint from the cable;
check the voltage value by multimeter between this
joint pin No.1 and power supply cathode; and observe
if it is around 12V.
No
Next step
Yes
Repair or
replace the
cable
3
Check if there is open circuit or short circuit to ground
of the canister control valve power supply ends circuit.
No
To step No.2
Yes
Next step
4
Check the resistance value if it is around 22-30Ω when
it is 20℃ between canister control valve pin No.1 and
pin No.2.
No
Replace the
valve
Yes
Diagnosis help
5
Check the voltage by the multimeter if it is around
3.7V between canister control valve joint pin No.1 and
power supply cathode.
No
Next step
Yes
Repair or
replace cable
6
Check if there is short circuit to ground between the
circuit of canister joint pin No.2 and ECU pin No. 46.
No
Diagnosis help
DTC: P0445 Much higher voltage of canister control valve drives grade control circuit
No.
Operating steps
Result
Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “ON”
Next step
Yes
To step No.4
2
Take off the canister control valve joint from the cable;
check the voltage value by multimeter between this joint
pin No.1 and power supply cathode; and observe if it is
around 12V.
No
Next step
Yes
Repair or replace
the cable
3
Check if there is open circuit or short circuit to ground of
the canister control valve power supply ends circuit.
No
To step No.2
Yes
Next step
4
Check the resistance value if it is around 22-30Ωwhen it
is 20℃ between canister control valve pin No.1 and pin
No.2.
No
Replace the
valve
Yes
Diagnosis help
5
Check the voltage by the multimeter if it is around 3.7V
between canister control valve joint pin No.1 and power
supply cathode.
No
Next step
Yes
Repair or replace
cable
6
Check if there is short circuit to power supply between
the circuit of canister joint pin No.2 and ECU pin No. 46.
No
Diagnosis help
CHERY·A21 SERVICE MANUAL ENGINE EFI SYSTEM
46
DTC: P0480 Air conditioner condenser cooling fan relay control circuit failure
No.
Operating steps
Result
Follow up
steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “OFF”
Next step
Yes
To step
No.4
2
Take off the air conditioner condenser cooling fan relay;
put the ignition switch to “ON” position, and check the
voltage value by multimeter between this relay power
supply end that is relay pin No.30, No.85 and power
supply cathode if it is around 12V.
No
Next step
Yes
Repair or
replace the
cable
3
Check if there is open circuit or short circuit to ground of
the air conditioner cooling fan relay power supply end
circuit.
No
To step
No.2
Yes
Replace
relay
4
Check the voltage by the multimeter if it is around 3.7V
between air conditioner condenser cooling fan relay
control ends that is relay pin No.86 and power supply
cathode.
No
Next step
Yes
Repair or
replace
cable
5
Check if there is open circuit or short circuit to power
supply or to ground between the circuit of relay control
end pin No.86 and ECU pin No. 50.
No
Diagnosis
help
DTC: P0500 Unreasonable failure of speed signal
No.
Operating steps
Result
Follow up steps
1
Connect the diagnostic tester and commutator, put the
ignition switch to “OFF”.
Next step
Yes
Check and
repair ABS
system
2
If it is a vehicle with ABS, please check if there is
ABS DTC.
No
Next step
Yes
Next step
3
Check if the speedometer finger works normally.
No
Check the
speedometer
line
Yes
Next step
4
Check if the speed sensor works normally.
No
Replace speed
sensor
Yes
Repair or
replace cable
5
Check if there is open circuit or short circuit to power
supply or to ground between the circuit of speed
sensor and ECU pin No. 59.
No
Diagnosis help
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст