Автомобили Chery: руководства по ТО — часть 10
!
! "
#
! !" ! #$
%
!
&
! &% & !
&
! % % '" %
#$
( &
) *
&%+ !
" !" !, (
% ' #$
(
& % !
* "
!
#$
&
)
!"
&+&%
"
( " %+
&%!
-
( ./0 *
" %1
)
!& % %
)) !*
"%&
)) !
!& %
!
2&
"
%! % !& %
)&
( 3
& % 4
" 1
( 3
% 5
))
2
( 3
6
%1 7
%+
TECHNICAL BULLETIN
Vehicle Model:
QQ+AMT
TB-E0145
Date: 26-09-07
Section: Transmission
Title:
Technical Bulletin about QQ AMT trouble code.
Affected range:
The transmission of all the QQ+AMT vehicle
Description:
This technical bulletin is the detailed information about the trouble code of
the QQ AMT transmission. It includes the meaning of each trouble code, the
possible reason of each code and the result if the trouble occurs. Knowing this
knowledge can help you to do diagnosis in some case.
C om p i l ed b y:
M i ke C hen
C hecked b y:
Sam Z hang
Ap p r ov ed b y:
F r ank Ouyang
PDF created with pdfFactory Pro trial version
Trouble code list of QQ AMT Transmission
1. Clutch Travel Sensor
P1741 short-circuit or short-circuit to power supply signal above 4.75V ON
Open-circuit or short-circuit to grounding wire signal less than 0.39V
Failure of parts or mechanic part failure of clutch speed, or the re-measurement of
clutch speed not equals to estimated speed.
Engine off, engine flameout, start failure and gearshift failure
Engine started, but incapable of upshifting to gear 2.
System auto settings can’t be started.
2. Gear Selector Travel Sensor
P1742 signal above limit value short-circuit or short-circuit to power supply
signal above 4.64V ON
Signal less than limit value open-circuit or short-circuit to grounding wire signal
less than 0.29V
Without effective signal failure of parts or mechanical part signal out of limit value
System incapable of upshifting to gear 2
System auto settings can’t be started.
3. Frication Plate Sensor
P1743 signal above limit value short-circuit or short-circuit to power supply
signal above 4.64V ON
Signal less than limit value open-circuit or short-circuit to grounding wire signal less
than 0.19v
Without effective signal circuit malfunction or out of dynamic scope electric signal
reception scope, but not verified between
the position indicator sensor and friction
plate speed signal.
System gearshift failure
In event of above malfunction, the vehicle speed should not exceed 4KM/H and the engine speed should not exceed
1,800RPM. Gear 1, gear 2 and reverse gear can be engaged, accelerator position is limited to below 45%, and the engine stop
and idling request are allowed.
4. System Pressure Sensor
P1744 signal above limit value short-circuit or short-circuit to power supply
signal above 4.88V ON
Signal less than limit value open-circuit or short-circuit to grounding wire
signal less than 0.24V
Without effective signal circuit malfunction sensor grounding wire not
connected
The pressure pump is activated at fixed time
System auto settings can’t be started.
PDF created with pdfFactory Pro trial version
5. Gearshift Lever Malfunction 0
P1745 signal above limit value short-circuit or short-circuit to power
supply signal above 4.5V ON
Signal less than limit value open-circuit or short-circuit to grounding wire signal
less than 0.5V
Without effective signal out of dynamic scope circuit malfunction
System automatically enters into automatic mode
The brake pedal must be depressed at engine start
The system will automatically engage gear 1 while the brake pedal keeps depressed.
It’s not allowed to shift to reverse gear
6. Gearshift Lever Malfunction 1
P1746 signal above limit value short-circuit or short-circuit to power
supply signal above 4.5V ON
Signal less than limit value open-circuit or short-circuit to grounding wire
signal less than 0.5V
Without effective signal out of dynamic scope circuit malfunction
System automatically enters into automatic mode
The brake pedal must be depressed at engine start
The system will automatically engage gear 1 while the brake pedal keeps depressed.
It’s not allowed to shift to reverse gear
7. Gearshift Lever Malfunction 2
P1748 signal above limit value short-circuit or short-circuit to power
supply signal above 4.5V ON
Signal less than limit value open-circuit or short-circuit to grounding wire
signal less than 0.5V
Without effective signal out of dynamic scope circuit malfunction
System automatically enters into automatic mode
The brake pedal must be depressed at engine start
The system will automatically engage gear 1 while the brake pedal keeps depressed.
It’s not allowed to shift to reverse gear
8. Gearshift Lever Malfunction 3
P1748 signal above limit value short-circuit or short-circuit to power
supply signal above 4.5V ON
Signal less than limit value open-circuit or short-circuit to grounding wire
signal less than 0.5V
Without effective signal out of dynamic scope circuit malfunction
System automatically enters into automatic mode
The brake pedal must be depressed at engine start
The system will automatically engage gear 1 while the brake pedal keeps depressed.
It’s not allowed to shift to reverse gear
PDF created with pdfFactory Pro trial version
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст