Chery A18. Manual — part 110
50
1.5
Disassemble nut for connecting knuckle and
control arm with 17# box wrench and 19# torque
wrench.
Moment of force: 75±5Nm
1.6
Disassemble driving nut with 30# torque wrench.
Moment of force: 265±5Nm
1.7
Disassemble screws of drive disc with Philips driver.
Moment of force: 8±2Nm
1.8
Disassemble knuckle with hands.
2.
Assembling step
2.1
Conduct assembly in contrary step of disassembly.
2.2
Precautions:
(1) It is necessary to renew brake fluid to brake system and adjust it in mode of air exhausting.
(2) Please check and adjust value of toein.
(3) Pay attention to fastening moment
51
V. Disassembly and assembly of underframe and stabilizer bar
1.
Disassembling step
1.1
Please disassemble fixed bolt of left suspension
with 13# wrench.。
Moment of force: 55±5 Nm。
1.2
Disassemble these three suspending bolts on right
side with 10# wrench.
Moment of force: 55±5Nm.
1.3
Please left vehicle with lifter, and hold engine with
lifting jack to avoid of falling.
1.4
Disassemble bolt for connecting underframe and
vehicle body with 18# box wrench.
Note: There is one bolt on each side of left and right.
Moment of force:130±10Nm。
1.5
Please disassemble bolt for connecting underframe
and stabilizer bar with 13# wrench.。
Note: There is one bolt on each side of left and right.
Moment of force: 35±3N·m
52
1.6
Please disassemble these two bolts for connecting
steering engine and underframe with 13# box
wrench.
Note: There are two bolts on each side of left and right.
Moment of force: 30N·m
1.7
Disassemble nut for connecting stabilizer bar and
control arm with 19# wrench.
Note: There is one bolt on each side of left and right, stabilizer bar is dismountable.
Moment of force:180±15Nm.
1.8
Please disassemble bolt for connecting underframe
and control arm with 19# torque wrench, and then
take down underframe and stabilizer bar.
Note: There is one bolt on each side of left and right.
Moment of force:130N·m
2.
Assembling step
Conduct assembly in contrary step of disassembly.
53
Section 2 Rear suspension
I.
Construction features
Rear suspension adopts leaf spring non-absolute suspension, which consists of leaf spring and absorber.
Rear bearing and leaf spring of rear suspension are connected to one integration, it is a kind of non-absolute
suspension construction, of which wheels on one side jump upwards and downwards while wheels on the other
side should be impacted correctively. During up/down jumping process of wheels, leaf spring should store energy
momentarily, and then release energy step by step. In this process, the device should absorb the energy via
damping effect of absorber and release them in other mode of energy to achieve damping effect. In additional,
comparing to spiral spring used by our Company, the leaf spring also has function of receiving and transiting
lateral force and longitudinal force.
II. Disassembly and assembly of rear suspension
1.
Disassembling step
1.1
Note: Jack up rear shaft to avoid of falling with
hydraulic jack.
1.2
Disassemble bolts and nuts of rear hanger plate of
steel plate with 19# and 22# wrench.
Moment of force: 180±5Nm
1.3
Disassemble bolts and nuts of front hanger plate of
steel plate with 19# box wrench and 22# torque
wrench.
Moment of force: 180±5Nm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст