Chery A18. Manual — part 35

SIZE OF CAMSHAFT JOURNAL AND
HOLE OF THE CYLINDER HEAD

Installation

To replace the cam shaft, observe the shape of the
rear end of the cam shaft for right selection.

Before installation, apply the cam of the cam shaft
with hyperbolic gear oil or motor oil. The cam
shaft shall be assembled from the cylinder head in
a back-to-front order.

Apply some motor oil to the thrust spacer of the
cam shaft and put the thrust spacer into the groove
of the cylinder head.

Screw two bolts into the threaded holes of the
thrust spacer and tighten them for a moment of
9—13Nm.

Check the axial clearance of the cam shaft, which
shall be within the specified range.

If adopting oversized hydraulic tappet (0.25), a
carefully selected cam shaft shall be used,
otherwise it will block the hydraulic tappet.

1. Standard size

2. Oversized (0.38)

Number of cam shaft

journal

Diameter of cam shaft journal

(unit: mm)

Diameter of the cam shaft hold of the

cylinder head (unit: mm)

1

45.12—45.14

45.163—45.188

2

45.37—45.39

45.413—45.438

3

45.62—45.64

45.663—45.688

4

45.87—45.89

45.913—45.938

5

46.12—46.14

45.163—45.188

Number of cam shaft

journal

Diameter of cam shaft journal

(unit: mm)

Diameter of the cam shaft hold of the

cylinder head (unit: mm)

1

44.74—44.76

44.783—44.808

2

44.99—45.01

45.033—45.058

3

45.24—45.26

45.283—45.308

4

45.49—45.51

45.533—45.558

5

45.74—45.76

45.783—45.808

CRANKSHAFT

CRANKSHAFT, CRANKSHAFT THRUST
SPACER, BEARING SHELL AND MAIN
BEARING CAP

Removal

Check the axial clearance of the crank shaft before
removal.

Kiss the end side of the crank shaft with the
contacts of a dial gauge (less degree of shrinkage).
Push the crank shaft away from the contacts and
adjust the dial gauge to 0, then push the crank shaft
to the direction of contacts as possible with a0 stout
carrying pole. Check the reading of the dial gauge,
which shall be the axial clearance. The axial
clearance of a crank shaft is 0.092-0.303mm.

The leaf of a clearance gauge can be used to check
the axial clearance of a crank shaft if there is no
dial gauge, which shall be placed between the third
main bearing cap and crank shaft (push and pull the
crank shaft).

Loosen the bolts and studs of the main bearing
shell, (beginning from the middle bearing cap),
take out the bolts and the threaded rods to remove
the main bearing cap and the lower shell of the
main bearing shell. This lower shell shall still
remain in the main bearing cap.

Take the crank shaft out.

Remove the crank shaft thrust spaces (2 pieces)
from the cylinder block.

Inspection

Check the main journal and main bearing shell
clearance.

Clean the main journal of the crank shaft, the
internal bore of the main bearing cap and main
bearing shell with a non-woven fabrics. Place the
plastic clearance gauge (its length slightly shorter
than the length of the main journal) on the main
journal, which shall be in parallel with the
generator of the main journal.

Note: Do not rotate the crank shaft！

Install the main bearing cap. Tighten the bolts of
the main bearing cap at the moment of 90-100N.m
by hands. Do not rotate the crank shaft.

Remove the main bearing bolts. Carefully take
out the main bearing cap and arrange them in order.
Read the bearing clearance according to the ratio
on the envelope of the plastic clearance gauge.
Check the bearing clearance from the third main
bearing and extend to both sides. The main bearing
clearance shall be 0.011—0.058mm.

Check the bearing clearance of the connecting rod.

Check the bearing clearance of the connecting rod
according to the above methods. The bearing
clearance of the connecting rod shall be 0.006—
0.06mm.

Size of connecting rod journal and connecting-rod bearing shell

Class

Diameter of

connecting rod

journal

(unit: mm)

Thickness of

connecting-rod

bearing shell

(unit: mm)

Standard

47.89—47.91

1.480—1.487

Downsized

by 0.025

47.89—47.91

1.492—1.499

Downsized

by 0.25

47.64—47.66

1.605—1.612

Downsized

by 0.5

47.39—47.41

1.730—1.737

Downsized

by 0.75

47.14—47.16

1.855—1.862

Downsized

by1.0

47.89—46.91

1.980—1.987

Diameter of main journal and size of main bearing shell

Class

Diameter of main

journal (unit: mm)

Diameter of the main bearing

bore of the cylinder block

(unit: mm)

Thickness of the main

bearing shell

(unit: mm)

Standard

57.98—58.00

62.2935+0.0065

2.131—2.138

Oversized by 0.4

57.98—58.00

62.6935+0.0065

2.331—2.338

Downsized by 0.02

57.98—58.00

62.2935+0.0065

2.141—2.148

Downsized by 0.25

57.73—57.75

62.2935+0.0065

2.256—2.263

Downsized by 0.50

57.48—57.50

62.2935+0.0065

2.381—2.388

Downsized by 0.75

57.23—57.25

62.2935+0.0065

2.506—2.513

Downsized by 0.25

and oversized by

0.4

57.73—57.75

62.6935+0.0065

2.456—2.463

Downsized by 0.50

and oversized by

0.4

57.48—57.50

62.6935+0.0065

2.518—2.558

Downsized by 0.75

and oversized by

0.4

57.23—57.25

62.6935+0.0065

2.706—2.713

Size of crank shaft thrust, thrust spacer and cylinder block thrust

Class

Size of cylinder block thrust

(unit: mm)

Size of crank shaft thrust

(unit: mm)

Thickness of thrust

spacer (unit: mm)

Standard

24+0.03

28.825-28.875

2.326+0.025

Oversized

by 0.38

24+0.03

29.205-29.255

2.516+0.025

2 thrust spacers