Chery A series. Manual — part 88
MEASUREMENT SYSTEM… … … . … … . … … . … … . …S-61
SUNROOF… … … . … … . … … . … … . … … . … … . …S-63
BRIEF INTRODUCTION OF SUNROOF’S MODEL AND FUNCTION… … … S-63
DESCRIPTION OF SUNROOF FUNCTION… … … . … … . … … …S-66
INSTRUCTIONS OF SUNROOF MAINTENANCE… … … . … … . … S-69
DISASSEMBLY AND ASSEMBLY OF SUNROOF… … … . … … . … S-72
REPLACEMENT OF GLASS PANEL… … … . … … . … … . … … S-76
REPLACEMENT OF SEAL… … … . … … . … … . … … . … S-78
REPLACEMENT OF SUNSHADE … … … . … … . … … . … … …S-82
PROGRAM DESCRIPTION… … … . … … . … … . … … . … S-90
NOTES ON MAINTENANCE AND USEAGE… … … . … … . … … …S-91
S-3
EXTERIOR ACCESSORIES
REMOVAL, INSTALLATION & ADJUSTMENT OF ENGINE HOOD
REMOVAL:
------Brace engine hood to remove washer
nozzle of windshield.
------Loosen the four screws securing engine
hood and hinges, two each side, while
the other operator removes the hood.
INSTALLATION:
------Install in the reverse order of removal.
ADJUSTMENT:
------To ensure an even clearance of 4 ±
0.5mm, consistent height and smooth
transition around the hood, the hinge is
designed with slot in it to make final
adjustment of engine hood.
------In making transverse adjustment of the
hood, loosen the bolt as shown in the
figure to move the hood till the desired
value is reached.
------In making vertical adjustment of the
front part of the hood, adjust the pin with
the rubber stopper to keep front fender
and engine hood on the same level.
S-4
REMOVAL & INSTALLATION OF HOOD LOCK
REMOVAL:
------Remove the upper hood lock. Tightening
torque for the bolt as shown in the figure is
14±2N·m.
------Remove the lower hood lock.. When
removing the grid of radiator, remove the
four screws on the central part to remove
front panel.
------When removing hood lock, loosen the cap
for the opening of release cable to drill off
the rivet between the lock and front panel.
------Remove pin and lock hook. Remove the
two screws between it and engine hood.
------Removal of lock handle. Take out the two
screws between the control panel and mud
guard from inside.
INSTALLATION:
-----Install in the reverse order of removal.
NOTE:Tightening torque for the upper bolts of
upper hood lock is 14±2 N.m.
S-5
REMOVAL & INSTALLATION OF FUEL FILLER CAP
REMOVAL:
----Loosen the two screws between the filler
cap and car body.
INSTALLATION:
----Install in the reverse order of installation
ADJUSTMENT:
----Keep the size at (4±0.5)mm and flatness
error between cap rim and the fender at
±0.5mm, which shall not affect the
appearance.
REMOVAL & INSTALLATION OF
EXTERIOR REARVIEW MIRROR
REMOVAL:
----In removing the mirror, relevant
instructions shall be followed to remove
front door trim panel (refer to REMOVAL
& INSTALLATION OF FRONT DOOR
TRIM PANEL)
----Remove inner triangular block of the
mirror.
----Remove the three screws connecting the
mirror and door trim panel. Pull the mirror
connector off to remove the mirror.
INSTALLATION:
----Install in the reverse order of removal.
Tightening torque for bolts is 3±0.3N·m.
REMOVAL & INSTALLATION OF
RADIATOR GRILLE
REMOVAL:
----Take out the four bolts between the grille
top and front end panel to remove radiator
grille as shown in the right figure.
INSTALLATION:
---- Install in the reverse order of removal.
Tightening torque for bolts is 3.5±2N·m.
S-6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст