Chery A series. Manual — part 41
Diagnostic trouble code: P0511 “Malfunction in control circuit of idle speed
regulator”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“ON” position.
Proceed to next step.
Yes
Proceed to next step.
2
Disconnect the connector of idle speed
regulator and inspect with multimeter to
verify that the resistances between pin A
and D, pin B and C are 53±5.3Ω under
20 .
℃
No
Replace the step
motor.
Yes
Repair or replace the
wiring harness.
3
Verify that the circuits between pin A, B,
C, and D of idle speed regulator and 65#,
66#, 67#, and 64# pin of ECU are open.
No
Refer to diagnosis
help.
G-53
Diagnostic trouble code: P0560 “Improper voltage signal of system”
Item
No.
Operation procedure
Inspection
results
Follow-up
procedure
1
Connect the diagnostic tester and adaptor,
and turn the ignition switch to “OFF”
position.
Proceed to next
step
Yes
Proceed to next
step.
2
Inspect with multimeter to verify that the
voltage of battery is about 12V.
No
Replace the battery.
Yes
Repair or replace
the wiring harness.
3
Verify that the resistances between the
44#, 45#, and 63# pins of ECU and 87#
pin of the main relay are open or short to
ground.
No
Proceed to next
step
Yes
Proceed to next
step
4
Start up the engine, and verify that the
charging voltage of generator is
maintained within 9-16V under different
speeds.
No
Replace the
generator.
Yes
Refer to diagnosis
help.
5
Verify that the earth point of engine
wiring harness is correct.
No
Repair or replace
the wiring harness.
G-54
Diagnostic trouble code: P0562 “Undervoltage of system”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“OFF” position.
Proceed to next step
Yes
Proceed to next step.
2
Inspect with multimeter to verify that
the voltage of battery is about 12V.
No
Replace the battery.
Yes
Repair or replace the
wiring harness.
3
Verify that the resistances between the
44#, 45#, and 63# pins of ECU and 87#
pin of the main relay are excessive.
No
Proceed to next step
Yes
Proceed to next step
4
Start up the engine, and verify that the
charging voltage of generator is
maintained within 9-16V under different
speeds.
No
Replace the
generator.
Yes
Refer to diagnosis
help.
5
Verify that the earth point of engine
wiring harness is correct.
No
Repair or replace the
wiring harness.
G-55
Diagnostic trouble code: P0563 “Overvoltage of system”
Item
No.
Operation procedure
Inspection
results
Follow-up
procedure
1
Connect the diagnostic tester and adaptor
and turn the ignition switch to “OFF”
position.
Proceed to next
step
Yes
Proceed to next
step
2
Inspect with multimeter to verify that the
voltage of battery is about 12V.
No
Replace the
battery.
Yes
Proceed to next
step
3
Start up the engine, and verify that the
charging voltage of generator is maintained
within 9-16V under different speeds.
No
Replace the
generator.
Yes
Refer to diagnosis
help.
4
Verify that the earth point of engine wiring
harness is correct.
No
Repair or replace
the wiring harness.
G-56
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст