Chery A series. Manual — part 119
Coolant
warning lamp
is always on.
The warning
lamp for
coolant is
always on
while driving,
whatever it’s
in cold
condition or
hot condition.
(1) Coolant level
in storage tank is
too low.
(2) Malfunction
of coolant level
switch.
(3) Malfunction
of warning switch
for coolant
temperature.
(4) Warning lamp
circuit is
grounded.
(1) Inspect to see whether
the engine coolant
temperature is actually too
high and the level of the
storage tank is too low.
(2) If all the above
inspection are normal, then
pull out the connector of
the storage tank level
switch. If the warning
lamp is off, it indicates that
the liquid level switch is
faulty.
(3) If the warning lamp is
still on, then connect the
connector of coolant level
switch and pull out the
connector of the coolant
temperature warning
switch. If the warning
lamp is off, it indicates that
the warning switch of
coolant temperature is
faulty; If the warning lamp
is still on, it indicates that
the circuit is grounded
somewhere.
Brake
warning lamp
is always on.
Brake
warning lamp
is still on even
if the hand
brake is
released.
(1) Brake oil level
is too low.
(2) Malfunction
of brake oil level
switch.
(3) Malfunction
of hand brake
switch.
(4) Warning lamp
circuit is faulty.
(1) Inspect to see whether
the brake oil level is too
low or not.
(2) If the oil level is
normal, then pull out the
connector of brake oil
level switch. If the
warning lamp is off, it
indicates that the brake oil
level switch is faulty.
(3) If the warning lamp is
still on, pull out the
connector of the brake
switch. If the warning
lamp is off, it indicates that
the brake switch is faulty;
If the warning lamp is still
on, it indicates that the
circuit is grounded
somewhere.
T-34
ELECTRIC WIPER AND WINDSHIELD WASHER SYSTEM
SYSTEM DESCRIPTION
The wiper is mainly consisted of the wiper motor assembly, the three-linkage mechanism,
and the pendulum rod and wiper blade with the tri-directional flexible ball joint. See figure
(wiper-1). The wiper motor is shown in figure (wiper-2).
Wiper
1. Permanent magnet DC motor
2. Worm-gear speed reducer
3. Wiper motor output shaft
Wiper motor(wiper-2)
The wiper motor is a speed reducer comprised of a mini permanent magnetic DC motor and a
worm-gear. In order to ensure that the pendulum rod and wiper blade could be positioned
under and parallel with low end of the front window each time after it has stopped. An
automatic stop conducting strip is installed on the back of the worm output shaft of the speed
reducer and 3 conducting contacts that contact with the conducting strip are installed on the
rear cover of the speed reducer. The strip and the contacts jointly perform the automatic stop
function together with the contact of the 0 position of wiper switch.
T-35
The washer is consisted of 5 parts which including a mini permanent magnet DC motor,
centrifugal water pump, nozzle, liquid storage container and water pipe. The motor and water
pump make up the assembly of the washer motor and the water pump as shown in figure
(Wiper-3):
1-Water inlet
2-Impeller blade
3-Pump body
4-Water outlet
5-Permanent magnet DC motor
Washer Motor(wiper-3)
As shown in figure (wiper-4), this assembly is installed on the liquid storage container and
make up the washer assembly together with the liquid storage container. The washer
assembly is installed on the left-hand impeller blade and the capacity of the liquid storage
container is 5.1 L.
Washer motor
Washer assembly(wiper-4)
T-36
The circuit schematic diagram of the front window wiper and washer of Chery sedan A15:
wiper switch
wiper motor
brown and yellow
black and gray
blown
horn
button
green and black
black and gray
blown
black and blue
green and black
green
and yellow
blown and blue
black and gray
green
green
green and red
washer
green
green and red
glay and black
Intermittent wiper relay
black and blue
black and blue
blown and black
to horn relay
The circuit schematic diagram of the front window wiper and washer.
T-37
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст